Kenwood KRF-V8881 D - Manual (Page 21)

WtüpíórWnMlM^
VR-2090/VR-?OaO/K RF-VS8810/ KRF-V7 7 710 {Cf^/ K)
The operations in this section consist of defining the relationship between the input selections displayed on the panel and the
components connected to the rear panel jacks*
' ^
General setup flow
□ Opening the “Setup"menu
S
Opening the “Setup IR" menu screen
El
Assigning connected components to the displayed
inputs
El
Completing the assignment of all the connected compo­
nents
Select the "Main Menu" icon.
nSaiii (ft fíat MG/ CD¡tf finpuil I
IS! Ä ^ T™ \£sM \
p pmcss^iSiiiHirm
t V i TVa Vld»>'l VKtooi vld*o3 Vldto4 *V AuS I i I
'liStn'Mode'^'
O Select the "Stp" icon in the "Main Menu" to display the
“Setup" menu.
Hcaai3iB@Ei3 •
Perform icon selection in the "Setup"menu.
f'
• The Setup' menu screeri shown on the left appears when the
"Stp" icon is selected.
lEWtiTEnèMEeEÌB^E
f Surround 1( Input li
( IR If Macro 1;
O Select the "IR" icon in the “Setup" menu to perform the IB
setup.
[ Download )[lVIulti Room 1
1
Assign the connected components to the inputs selected with the ¡pipyj
Select an input jack name, consult the Setup Codes chart {on the attached sheet! to fittd out the setup code corresponding to the
component connected to the selected input, and input the corresponding 4-dSgit code to assign it to the selected input.
Setup JR
#9990 :0©(U(2) { >
iQ®©
iQ®@ '• [Check t 0
When using digital inputs, perform connection and assignment
taking special care in the relations between the input jacks and
connection cords.
DIGITAL INPUT jack Usable cord connector
VIDE02 OPTICAL connector
VIDEOS OPTICAL connector
VIDE04 COAXIAL connector
CD! COAXIAL connector
When registering setupcodesfor KENWOOD audio components
which are connected to this unit by system control cords, use th e
following codes to insure proper system control operation:
Cassette : 7990
Single CD : 8990
Carrousel CD : 8991
200-disc changer CD : 8992
iMulti-roorri capability CD)
MD : 9990
Set "CD2" when using a rmiiti-room
capable CD player, -CS] -S£
O Select the "Q)“or "Q " icon to select an input.
The section showitig "MD/Tapel" in the figure displays the
current input selection.
■ Yhe inputs are switched every time
^Stape 1
!Tape2S
TV1
TVZ
*1;
Video!
Vidso2
Videos
- Video4
Q Find out the setup code of the actually connected compo­
nent from the Setup Codes chart and input the code using
icons ¡T| to [ q 1 .
[Example)
To assign a KENWOOD MD recorder : [|] [f} [|] [o] Entr
© The input setup code can be...
Cheeked by selecting the "Cheek" icon.
iThis results in turning the component power on if it has been set
so. However, the components with which the input of system
control setup codes is required and certain components from
other manufacturers than KENWOOD cannot be turned on.)
Cleared by selecting the "CIr" icon.
Select the "Entr" icon to enter the selection in memory,
• Section "MD" on the “Setup IR" menu screen shows the
component connected to the input jacks on the rear panel.
Assign all the connected components.
Repeat step B for each component connected.