Kenwood KRF-V8881 D - Manual (Page 61)

VR' 2090 /VR^£ 0 SO/Kfìf'VS 8 ai D/KRF-V7771D (En/К)
Available play mode£
The following table shows the relationship between the source signal, source component and receiver input, and the play mode
than can be selected from the surround menu.
Source Signal Source Component Receiver Input
Play Modes That Can be Selected from
"Lstn Mode" menu
DTS CD / LD / DVD *1 Digital DTS / Stereo
Dolby Digital (AC-3Ì DVD Digital Dolby Digital / Stereo *2
Dolby Digital (AC-3) RF LD {DEMODULATOR) Digital Dolby Digital / Stereo *2
PCM / Analog CD / LD / DVD etc. Digitai / Analog Pro Logic / 3 Stereo / Stereo / DSP mode
*1 Playback is possible if the source ootnponent is a DTS compat­
ible player. Refer to the instruction manual of your player to
check if DTS compatibie.
*2 When the Dolby Digital (AC-3) signal has 2 or 2.1 channels, it can
be played using Pro Logic or 3 Stereo mode.
CaMoj^LWjmiMBM.
During playback of a DTS source
• The "Input Analog” mode cannot be selected during playback of a DTS source,
I Dependnig on'thTidayerln 'u^e^noi'sfriiw be ^eTerated depending on the operation method employed for DTS play. When playing a DTS source,
wait until "DTS" is displayed before proceeding to the desired operation.
Input
Signal
Panel DTS
LCD Display
Play Mode indicator Lstn Mode Status
DTS DTS Lights DTS DTS
DTS Dolby Digital Blinks DTS Dolby Digital
DTS PCM Blinks DTS PCM
Display dun ng playback in Digital (Dolby Digital) mode
Input
Signal
Panel LCD Display
Play Mode
Dolbv Digitai
Indieatdr Lstn Mode Status
Dolby Digital DTS Blinks Dolby Digital DTS
[ Dolby Digital Dolby Digital Lights Dolby Digital Dolby Digital
Dolby Digital PCM Blinks Dolby Digital PCM
Display during playback in PCM mode
Surround
Play Mode
PCM
Input
Signal
DTS
Pa«ei
Doiby Digital
Indicator
LCD Display
Lstn Mode Status
Lights off *3 DTS
PCM Dolby Digital Lights off *3 Dolby Digital
PCM PCM Lights off *3 PCM
»3 Pro Logie, 3 stereo or Stereo.
During analog playback
m Noise IS generated when a DTS source is played. Switch to "Input Digital" before playing s DTS source.
During "Digital Auto " play
During "Digital Manual"play
. Tho BBiPctinn of the "Surround" icon may be restricted depending on the input signal. . . , , , _____
. After Dowensswitched ON/OFF (Of theON/STANDBYkey is pressed to switch over to the STANDBY orON mode), when the speakers are s w t c
• Afterpower isswitcneou wur-r-ioi u .-ninttat Mamial" Olavback "Diaital Manual" is switched automatically to "Digital Auto .
ON/OFF or when the anaSoq input IS selected after Digital ivianuai piayoacK, mgimi mauua. ^ . 3 . „„ ,s,k„r i„r3, than
,, I I , - _.*n/nfOnH.anrrasiinr? inhanncliAC-TIftoutintheProLooiCord tîteteo mode or other input tna
• Use the "Digital Manual mode when playing a 2/0 (2channel or 2 .1 cnenney ew, j inpuim ui - r ^ i-uy
2/0 S2 channel or 2,1 channel] signal in Stereo mode. ^ ma^í «rwitrh "Lain Mode"
During "Digital Auto” playback of certain DVD and LD players, performing operations such as Skip or Stop may switch Lstn
automatically to the surround m.ode intended fot the input signal.