Chapter 2 tuning procedures 47 – MTS Series 793 User Manual
Page 4
MTS Series 793 Tuning and Calibration
Contents
4
System Calibration 44
Sensor Calibration 45
When to Tune 49
Tuning for the First Time 52
How To Warm Up Station Hydraulics 53
How to Set Servovalve Polarity 56
How to Balance the Servovalve 60
How to Adjust Dither 67
How to Manually Tune the Control Loop 70
Tuning the Displacement Control Mode 71
Tuning the Force Control Mode 76
Tuning the Strain Control Mode 82
How to Perform Advanced Tuning Techniques 88
How to Auto-Tune 88
How to Manually Tune Three-Stage Servovalves 93
Zero the Spool Position Signal 99
How to Monitor Inner Loop Signals 100
How to Use Error to Tune I Gain 102
About the Cascaded PIDF Control Mode 104
How to Tune a Cascaded PIDF Control Mode 104
About Channel Limited Channel (CLC) Control Modes 106
How to Tune a CLC Control Mode 107
About Dual Compensation Control Modes 110
How to Tune a Dual Compensation Control Mode 112
About Tuning Filters 115
How to Enable a Tuning Filter 119
- Series 111 Accumulator (40 pages)
- Series 249G2 Swivels (34 pages)
- Series 201 Actuators (40 pages)
- Series 215 Rotary Actuator (68 pages)
- Series 242 Actuators (40 pages)
- Series 244 Actuators (68 pages)
- Series 247 Actuators (40 pages)
- Series 248 Actuators (46 pages)
- 709 Alignment System (158 pages)
- Series 609 Alignment Fixture (70 pages)
- 494 Controller Hardware FT 40 (344 pages)
- ReNew Technical Reference (50 pages)
- DCPD Measurement System (46 pages)
- Bionix EnviroBath (40 pages)
- FGW900 High-temperature Furnace (38 pages)
- Model 409.83 Temperature Controller (40 pages)
- Series 651 Environmental Chambers (30 pages)
- Series 653 High-Temperature Furnaces (38 pages)
- Series 658 Environmental Chamber (24 pages)
- Series FEC Environmental Chamber (48 pages)
- Model 685.53 Grip Control Module (24 pages)
- Series 685 Hydraulic Grip Supply (48 pages)
- Bend Fixture-10 kN (2 pages)
- Grip-Manual Bend Fixture-100 kN (2 pages)
- Grip-Manual Bollard-2 kN (2 pages)
- Grip-Manual Bollard-500 N (2 pages)
- Compression Platen-100 kN-100mm (2 pages)
- Compression Platen-100 kN-150mm (2 pages)
- Compression Platen-100 kN-200mm (2 pages)
- Compression Platen-20 kN (2 pages)
- Compression Platen-20 kN-100mm (2 pages)
- Compression Platen-20 kN-200mm (2 pages)
- Compression Platen-20 kN-SST (2 pages)
- Compression Platen-500 N FYC502A (2 pages)
- Compression Platen-500 N FYB502A (2 pages)
- Compression Platen-500 N-50mm (2 pages)
- Grip-Pneumatic Vise-Style-1 kN (2 pages)
- Pneumatic Bollard-500 N (2 pages)
- Scissor-Style-2 kN (2 pages)
- Scissor-Style-5 kN (2 pages)
- Screw-Style-5 kN (2 pages)
- Screw-Style-5 kN-SST (2 pages)
- Bend Fixture-1000 kN (2 pages)
- Bend Fixture-300 kN (2 pages)
- Bolt Grips (32 pages)