MTS Series 793 User Manual
Page 132
MTS Series 793 Tuning and Calibration
Displacement Sensor Calibration
Calibration Procedures
132
Displacement Sensor Calibration: Abbreviated Procedure
The following abbreviated procedure outlines a displacement sensor (LVDT)
calibration process. More detailed calibration information is available on the
pages listed.
Task 1, “Get things ready,”
on page 133
Task 2, “Turn on hydraulic pressure,”
on page 136
Task 3, “Verify the conditioner polarity,”
on page 137
Task 4, “Set the phase,”
on page 137
Task 5, “Set the zero and offset,”
on page 138
Task 6, “Gain/Delta K Calibration,”
on page 142
Note
The Gain/Linearization Calibration procedure applies only to controllers
equipped with full-range conditioners (e.g. Model 493.25 DUCs).
Task 7, “Gain/Linearization Calibration,”
on page 147
Task 8, “Save the calibration,”
Note
Controllers equipped with full-range conditioners (e.g. Model 493.25
DUCs) do not require multiple ranges.
Task 9, “Calibrate additional ranges,”
on page 155
- Series 111 Accumulator (40 pages)
- Series 249G2 Swivels (34 pages)
- Series 201 Actuators (40 pages)
- Series 215 Rotary Actuator (68 pages)
- Series 242 Actuators (40 pages)
- Series 244 Actuators (68 pages)
- Series 247 Actuators (40 pages)
- Series 248 Actuators (46 pages)
- 709 Alignment System (158 pages)
- Series 609 Alignment Fixture (70 pages)
- 494 Controller Hardware FT 40 (344 pages)
- ReNew Technical Reference (50 pages)
- DCPD Measurement System (46 pages)
- Bionix EnviroBath (40 pages)
- FGW900 High-temperature Furnace (38 pages)
- Model 409.83 Temperature Controller (40 pages)
- Series 651 Environmental Chambers (30 pages)
- Series 653 High-Temperature Furnaces (38 pages)
- Series 658 Environmental Chamber (24 pages)
- Series FEC Environmental Chamber (48 pages)
- Model 685.53 Grip Control Module (24 pages)
- Series 685 Hydraulic Grip Supply (48 pages)
- Bend Fixture-10 kN (2 pages)
- Grip-Manual Bend Fixture-100 kN (2 pages)
- Grip-Manual Bollard-2 kN (2 pages)
- Grip-Manual Bollard-500 N (2 pages)
- Compression Platen-100 kN-100mm (2 pages)
- Compression Platen-100 kN-150mm (2 pages)
- Compression Platen-100 kN-200mm (2 pages)
- Compression Platen-20 kN (2 pages)
- Compression Platen-20 kN-100mm (2 pages)
- Compression Platen-20 kN-200mm (2 pages)
- Compression Platen-20 kN-SST (2 pages)
- Compression Platen-500 N FYC502A (2 pages)
- Compression Platen-500 N FYB502A (2 pages)
- Compression Platen-500 N-50mm (2 pages)
- Grip-Pneumatic Vise-Style-1 kN (2 pages)
- Pneumatic Bollard-500 N (2 pages)
- Scissor-Style-2 kN (2 pages)
- Scissor-Style-5 kN (2 pages)
- Screw-Style-5 kN (2 pages)
- Screw-Style-5 kN-SST (2 pages)
- Bend Fixture-1000 kN (2 pages)
- Bend Fixture-300 kN (2 pages)
- Bolt Grips (32 pages)