Force sensor calibration: abbreviated procedure – MTS Series 793 User Manual
Page 158
MTS Series 793 Tuning and Calibration
Force Sensor Calibration
Calibration Procedures
158
Force Sensor Calibration: Abbreviated Procedure
The following abbreviated procedure outlines a force sensor (load cell)
calibration process. More detailed calibration information is available on the
pages listed.
Task 2, “Turn on hydraulic pressure,”
Task 3, “Verify the conditioner polarity,”
on page 162
Task 4, “Set the zero and offset,”
on page 163
Task 5, “Gain/Delta K Calibration,”
on page 163
Note
The Gain/Linearization Calibration procedure applies only to controllers
equipped with full-range conditioners (e.g., Model 493.25 DUC module).
Task 6, “Gain/Linearization Calibration,”
Task 7, “Millivolt/Volt Calibration,”
Task 8, “Establish the shunt calibration reference,”
on page 182
Task 9, “Save the calibration,”
on page 186
Note
Controllers equipped with full-range conditioners (e.g., Model 493.25
DUC module) do not provide or require multiple ranges.
Task 10, “Calibrate additional ranges,”
on page 187
- Series 111 Accumulator (40 pages)
- Series 249G2 Swivels (34 pages)
- Series 201 Actuators (40 pages)
- Series 215 Rotary Actuator (68 pages)
- Series 242 Actuators (40 pages)
- Series 244 Actuators (68 pages)
- Series 247 Actuators (40 pages)
- Series 248 Actuators (46 pages)
- 709 Alignment System (158 pages)
- Series 609 Alignment Fixture (70 pages)
- 494 Controller Hardware FT 40 (344 pages)
- ReNew Technical Reference (50 pages)
- DCPD Measurement System (46 pages)
- Bionix EnviroBath (40 pages)
- FGW900 High-temperature Furnace (38 pages)
- Model 409.83 Temperature Controller (40 pages)
- Series 651 Environmental Chambers (30 pages)
- Series 653 High-Temperature Furnaces (38 pages)
- Series 658 Environmental Chamber (24 pages)
- Series FEC Environmental Chamber (48 pages)
- Model 685.53 Grip Control Module (24 pages)
- Series 685 Hydraulic Grip Supply (48 pages)
- Bend Fixture-10 kN (2 pages)
- Grip-Manual Bend Fixture-100 kN (2 pages)
- Grip-Manual Bollard-2 kN (2 pages)
- Grip-Manual Bollard-500 N (2 pages)
- Compression Platen-100 kN-100mm (2 pages)
- Compression Platen-100 kN-150mm (2 pages)
- Compression Platen-100 kN-200mm (2 pages)
- Compression Platen-20 kN (2 pages)
- Compression Platen-20 kN-100mm (2 pages)
- Compression Platen-20 kN-200mm (2 pages)
- Compression Platen-20 kN-SST (2 pages)
- Compression Platen-500 N FYC502A (2 pages)
- Compression Platen-500 N FYB502A (2 pages)
- Compression Platen-500 N-50mm (2 pages)
- Grip-Pneumatic Vise-Style-1 kN (2 pages)
- Pneumatic Bollard-500 N (2 pages)
- Scissor-Style-2 kN (2 pages)
- Scissor-Style-5 kN (2 pages)
- Screw-Style-5 kN (2 pages)
- Screw-Style-5 kN-SST (2 pages)
- Bend Fixture-1000 kN (2 pages)
- Bend Fixture-300 kN (2 pages)
- Bolt Grips (32 pages)