Balboa Water Group Titan Bath Control - Manual (Page 6)

Manufactured under one or more of these patents. U.S. Patents: 5332944, 5361215, 5550753, 5559720, 5,883,459, 6253227, 6282370, 6590188, 6976052, 6965815, 7030343, 7,417,
834 b2, Canadian Patent: 2342614, Australian patent: 2373248 other patents both foreign and domestic applied for and pending. All material copyright of Balboa Water Group.
6 7/14/14
sensors
It is highly recommended to install a water level sensor. The
sensor affects the pump and blower purge. If there is no water
sensor, the pump can run any time, even when the water level
falls below acceptable levels for safe pump operation.
When
there is a water sensor, the pump can only run when there is
water detected. The water temp sensor also cuts off if the
water temperature goes beyond 111 degrees.
temPerature and tImer dIsPlay
On panels with 3-digit displays, the user can select whether
to show the water equipment timer, the temperature, or
both alternating.
The temperature will be displayed in 0.5 steps in C, and full
steps in F. No degree symbol will be shown. The timer value
will be displayed as 2 digits preceded by the letter “t”. If no
temperature sensor is present, only the timer value will be
displayed. The temperature sensor is usable at all times.
The panel will be able to communicate bidirectionally with any
module(s) it is connected to. Each module will acknowledge
its working state and report any errors it can determine. In the
case of an error, an error code will display.
tItan Bath controls suPPort 3 Panels:
• 6-button LED lit icons, and 3-digit LED message display
• 4-button with 4 point LEDs
• 2-button with 3-digit LED message display
6 and 2 Button Panels
On the 6-button panel, button icon LEDs change in brightness.
Under normal operation, a bright button indicates the function is
on. A dim button indicates the function is available but not on. A
blank button indicates the function is not available. Exceptions
in brightness will occur as when powering up, or when selecting
a Configuration.
Off function: If the pump is running and pump-related
equipment like waterfall and/or pillow is running, then turning
off the pump turns the related equipment off also.
4 Button Panel
On the 4-button panel, the 4 point LEDs can indicate Error, On
state, Water Present, and User Preset. When there is an error,
the Error light will indicate such, while the other 3 LEDs will
indicate the error number in binary code. At power up, all 4 LEDs
will briefly display the configuration number in binary code.
Off function: If the pump is running and pump-related
equipment like waterfall and/or pillow is running, turning off the
pump turns the related equipment off at the same time.
system tImer
The System Timer is started any time any water equipment is
turned on. The System Timer defaults to 20 minutes; the user
can change this, in User Preferences mode.
user Button
• Until you program it, the User button functions as an “all
off” button. In other words, the default User Preset turns all
equipment off.
• Pressing and holding the User button memorizes the current
state of all equipment as a User Preset. Pressing (but not
holding) the User button recalls the last-memorized User
Preset.
• If it’s programmed as a user button and you want to return it to
an “all off” button again, turn everything off and re-save.
Titan Bath Control Behavioral Specs
Buttons WIth tWo oPtIons
A user guide may designate a bath button panel as having a
dual function, “Light/Aux” for example on the two button panel.
Depending on the equipment installed, the button configuration
must be inputted according to the equipment shown on the
configuration table (as a pillow, for example). In this case, AUX
would designate the function for the pillow.