IAI America SSPDACR - Manual (Page 107)

15.
Appendix
99
15.1.10 ISDBCR, ISPDBCR-LX
L Weight [kg]
200 W motor 400 W motor 200 W motor 400 W motor
Stroke
Without
brake
With
brake
Without
brake
With
brake
B D E F
Without
brake
With
brake
Without
brake
With
brake
1000 1489 1523 1511 1545 1350 4 16 173.5 29.8 30.3 30.2 30.7
1100 1589 1623 1611 1645 1450 5 18 73.5 31.5 32.0 31.9 32.4
1200 1689 1723 1711 1745 1550 5 18 173.5 33.2 33.7 33.6 34.1
1300 1789 1823 1811 1845 1650 6 20 73.5 35.0 35.5 35.4 35.9
1400 1889 1923 1911 1945 1750 6 20 173.5 36.7 37.2 37.1 37.6
1500 1989 2023 2011 2045 1850 7 22 73.5 38.4 38.9 38.8 39.3
1600 2089 2123 2111 2145 1950 7 22 173.5 40.2 40.7 40.6 41.1
1700 2189 2223 2211 2245 2050 8 24 73.5 41.9 42.4 42.3 42.8
1800 2289 2323 2311 2345 2150 8 24 173.5 43.6 44.1 44.0 44.5
1900 2389 2423 2411 2445 2250 9 26 73.5 45.4 45.9 45.8 46.3
2000 2489 2523 2511 2545 2350 9 26 173.5 47.1 47.6 47.5 48.0
2100 2589 2623 2611 2645 2450 10 28 73.5 48.8 49.3 49.2 49.7
2200 2689 2723 2711 2745 2550 10 28 173.5 50.6 51.1 51.0 51.5
2300 2789 2623 2811 2845 2650 11 30 73.5 52.3 52.8 52.7 53.2
2400 2889 2923 2911 2945 1750 11 30 173.5 54.0 54.5 54.4 54.9
2500 2989 3023 3011 3045 2850 12 32 73.5 55.8 56.3 56.2 56.7
A
B
21
1
6
140 5
150 32.5
77
5.
18
74
22
2 116
144
149 5 53 5 67 Stroke
117 200W
139 400W
B 22
L
220
M.E. S.E. M.E. HOME
300
03
1
20.
0±
03
1
7
75 75
90 30 30
120 15 15
150
168
168
150 D×200 100 70.5
145.5
F
02
1
20.
0±
75
01
56
106 50
02
1
25
12
8 H7 0
+0.015
39
3.
4
3.
7
1.5 4.5
6
Ø
Detail View A
2- 8 H7, depth 10
Reference
surface
8-M8, depth 20
10 (from the reference surface)
2-oblong , depth 10
Cable exit direction: Right
Grease nipple for ball screw
Screw for grounding wire
connection (M4 x 2 locations)
Base installation surface for high-precision
guide specification
Machining jig holes are
provided across the bottom
surface of the base.
These holes are not used to
install the actuator.
Plug with rubber grommets.
Reference
surface
4- 8, H7 depth 10
E-M8 depth 20
Slider center position (home)
Cable exit direction: Left
Cable length
Reference
surface
Grease nipple for guide (for supplying oil to the
guide on the installation surface side)
B (Same on the opposite side of grease nipples)
Cable exit direction: Rear
Air tube joint
Applicable tube outer diameter: 12
(Inner diameter: 5)
(Plug with plug screw Rc 3/8 on the
opposite side)
151 (200W BK type)
173 (400W BK type)
Joint installation position: Standard
Joint installation position: Opposite side