TransAct Technologies ITHERM 280 User Manual

Page 348

Index

iTherm

280 Programmer’s Guide

Page 346

Rev C

28-07764

Graphic Data, Processing, 127
Graphic Mode, Reassigning, 124
Graphic mode, Set Horizontal, 128
Graphic save, 129
Graphics

all-points-addressable (APA), 244
Character, 241
color, 127
horizontal, 127
Horizontal, 244
printing, 241

GS - <0> x y d

…d(x x y x 8)Define user-

defined bit image, 231

GS ! Set character size, 201
GS # Insert Euro character, 198
GS * x y d

… d(x x y x 8) Define single user-defined

bit-image, 234

GS / Print single user-defined bit-image, 235
GS ^ r t m Execute macro, 230
GS _ Delete start-up macro definition, 231
GS 0 <0> Print user-defined bit image, 233
GS 1 <0> Erase single entry from

nonvolatile memory, 233

GS 3 Query nonvolatile memory pool information,

235

GS 5 Erase all entries from nonvolatile memory pool,

233

GS 6 <0> Save user-defined character set,

235

GS 7 <0> Select user-defined character set,

235

GS f Select font for HRI characters, 222
GS H Select printing position of HRI characters,

221

GS h Set bar code height, 221
GS k

> …

> NUL Print bar code, 220

GS L

> Set left margin, 207

GS w Set bar code width, 222
GS W

> Set printing area width, 207

Home, Returning, 208
Horizontal Motion Control, 83
Horizontal Position, Setting, 84
Horizontal Tab, 83
Horizontal Tab Positions, Setting, 207
Horizontal tab Stops, Setting, 83
Horizontal Tab, Setting, 206
IEEE 1284 buffer, Clearing, 173
Indicator Lights, 56
Indicators

Fault, 56

Initialize maintenance counter, 228
Initialize the Printer, 163, 224
Ink Cartridges

Ordering, 341

Inquire Commands, 172
Installing Cables, 41
Installing New Interface Cards, 40
Installing Paper, 43
Intercharacter Spacing, Setting, 95
International Character Set, Selecting, 101, 102, 195,

270, 271, 272, 276, 277, 278, 279, 283, 284, 285,
286, 287, 288

International Character Sets, 195
IPCL Codes, 74
Ithaca Specific iTherm™ 280 Commands, 236
Justification, Selecting, 206
Justification, Setting, 84
LED indicator

error, 56
paper, 56
power, 56

Level 0 diagnostics, 61
Line feed, 82
Line Feed Button, 55
Line Feed, Performing, 85
Line Feed, Reverse, 90
Line Spacing Commands, 193
Line Spacing, Enabling, 87
Line Spacing, Feeding Lines, 87
Line Spacing, Select Default, 193
Line Spacing, Set at 2 ½, 16-inch and 7/72 inch, 86
Line Spacing, Set-1/8 inch, 86
Line Spacing, Set-n/216 inch, 85
Line Spacing, Setting, 193
Line Spacing-Variable, Setting, 86
Machanical Error Status, Inquire, 174
Macro Data, Run from user Store, 134
Macro Data, Saving, 130
Macro Data, Saving in user Store, 133
Macro Record, Beginning, 130
Macro Record, Ending, 133
Macro Record, Ending name, 130
Macro Record, Start, 138
Macro Record, Starting, 130, 132
Macro Record, Stop, 138
Macro Record, Stop and Save, 138
Macro Record, Stopping, 130
Macro, Flag on Startup, 134
Macro-Function Commands, 230
Mechanism Control Commands, 223
Microline Emulation, 74
Miscellaneous Commands, 224
Multidrop configuration, 318
Multi-Drop Control, Beginning, 170
Multiline Mode, 108
OFF Button, 55
Off-line active, 319
One Line/Double Wide Print, Beginning, 107
One Line/Double Wide Print, Canceling, 107
Output Paper end Signals, Selecting Paper Sensors,

165, 204

Panel Button Commands, 202
paper Feed, Enable, Disable, 164, 202
Paper Feed, Enable/Disable, 236
Paper Low Sensor, 236
Paper Motion, 82
Paper Out Sensor, disable, 161
Paper Out Sensor, enabling, 161
Paper Out Status, Inquire, 173
Paper Sensor Commands, 203
Paper Sensors, Selecting to Stop Printing, 165, 203
Parallel Interface Connector, 42
Parallel port timing, 304
PcOS Control Codes, 75