TransAct Technologies ITHERM 280 - Manual (Page 346)

Index iTherm ® 280 Programmer’s Guide
Page 344 Rev C 28-07764
[ESC] a Set justification, 84
[ESC] A Set variable line spacing to n/72 inch, 86
[ESC] b ... Print bar code, 139, 146, 179, 180
[ESC] B
1
>
2
> …
i
> 0 Set vertical tab stops,
88
[ESC] Begin 12 cpi, 93
[ESC] BEL Sound buzzer, 223
[ESC] C [NUL] Set form length in inches, 89
[ESC] c Select color, 107
[ESC] C Set form length in lines, 89
[ESC] c 3 Select paper sensor(s) to output paper-
end signals, 204, 236
[ESC] c 4 Select paper sensor(s) to stop printing,
203, 236
[ESC] c 5 Enable/disable paper feed, 202, 236
[ESC] d Feed lines at current spacing, 87
[ESC] d Print and feed lines, 191
[ESC] D
1
>
2
>
3
> …
i
> 0 Set horizontal tab
stops, 83
[ESC] D
1
> …
k
> NUL Set horizontal tab
positions, 207
[ESC] e Print and reverse feed lines, 191
[ESC] E Turn on/off emphasized mode, 199
[ESC] E Begin emphasized print, 110
[ESC] F End emphasized print, 111
[ESC] f Select receipt station, 115, 116, 119, 120, 121,
122
[ESC] g <0> Process user macro, 138
[ESC] g <1> Start macro record, 130, 138
[ESC] g <2> Stop macro record, 130, 138
[ESC] g <3> Stop macro record and save, 138
[ESC] G Turn on/off double-strike mode, 200
[ESC] G Begin enhanced print, 110
[ESC] h Process
color graphics, 127
[ESC] h Process
horizontal graphics, 127
[ESC] H End enhanced print, 110
[ESC] I Set print quality mode, 96
[ESC] i Partial knife cut, 223
[ESC] J Fine line feed, 85
[ESC] J Fine linefeed, 151, 152, 153, 154
[ESC] J Print and feed paper, 192
[ESC] j Print and reverse feed, 192
[ESC] K Print and reverse feed lines, 192
[ESC] K
1
>
2
> Print single-density graphics, 123
[ESC] L
1
>
2
> Print half-speed double-density
graphics, 123
[ESC] l Electronic Journal Carbon Copy, 160
[ESC] M Select character font table, 194
[ESC] m Perform a partial knife cut, 223
[ESC] p
1
>
2
> Generate pulse, 225
[ESC] P Begin rotated font, 97
[ESC] p 3 Select paper sensor(s) to output paper-
end signals, 165
[ESC] p 4 Select paper sensor(s) to stop printing,
165
[ESC] p 5 Enable/disable paper feed, 164
[ESC] q Query marker, 162
[ESC] Q Set right margin, 208
[ESC] R Select an international character set, 195
[ESC] r Turn color mode on/off, 198
[ESC] R Reset horizontal and vertical tab stops, 84, 88
[ESC] S <0> Select superscript, 111
[ESC] S <1> Select subscript, 111
[ESC] SP Set right-side character spacing, 193
[ESC] t Select character code table, 198
[ESC] T End superscript or subscript, 111
[ESC] U <0> Begin bi-directional print, 126
[ESC] U <1> Begin unidirectional print, 125
[ESC] U Turn on/off unidirectional printing
mode, 207
[ESC] V Set intercharacter spacing, 95
[ESC] V Turn on/off 90
°
rotation mode, 200
[ESC] W Double-wide, double-high mode, 108
[ESC] w Enable dynamic response, 154
[ESC] x Open cash drawer, 163
[ESC] X
1
>
2
> Set left/right print margin, 161
[ESC] y Set feature control, 167
[ESC] Y
1
>
2
> Print full-speed double-density
graphics, 124
[ESC] Z
1
>
2
> Print quad-density graphics, 124
[FF] Set form feed, 89, 91
[GS] \
l
>
h
> Set relative vertical print position in
page mode, 220
[GS] a Enable/disable Automatic Status Back,
210
[GS] b Turns smoothing on/off, 201
[GS] c Print counter, 228
[GS] g 0 Initialize maintenance counter, 228
[GS] g 2 Transmits maintenance counter, 229
[GS] I Transmit printer ID, 224
[GS] P x y Set horizontal and vertical motion units,
224
[GS] r Transmit status, 212
[GS] Start/end macro definition, 230
[GS] V Select cut mode and cut paper, 223
[HT] Set horizontal tab, 83, 206
[LF] Print and line feed, 191
[LF] Set line feed, 82
[SI] Begin 17 cpi, 93
[SO] Begin one-line double-wide print, 107
[SOH] Begin multi-drop control, 170
[VT] Set vertical tab, 88
10 CPI Character Pitch, Beginning, 93
12 CPI Character Pitch, Beginning, 93
12 x 12 Draft Print Mode, Beginning, 96
17 CPI Character Pitch, Beginning, 93
24 CPI Character Pitch, Beginning, 93
APA Graphics, Printing, 124
Appendix A
Ordering Supplies, 341
Application Development, 74
Audio Alert, Configuring, 164
Auido alert, 164
Auto cut, Performing, 163
Auto Line Feed, Beginning, 90
Automatic Status back, Enable/Disable, 210
Back Space, 83
Bar Code Commands, 220
Bar Code, Print, 139, 146, 179, 180
Bar Code, Set height, 147
Bar Code, Set Justification, Print Direction, 148
Bar Codes, 139