TANDBERG 6000MXP - Manual (Page 68)

68
TANDBERG 3000 MXP & 6000 MXP
REFERENCE GUIDE FOR SYSTEM INTEGRATORS
Configuration-type Commands – xconfiguration / configuration.xml
D 13887.08
MAY 2008
Audio Stereo:
Turns stereo I/O mode On or Off.
Example: xconfiguration audio stereo: on
Stereo Settings Output Response Codec 3000 MXP Output Response Codec 6000 MXP
Out 1
mode Stereo
I/O mode
Stereo
speakers
Audio Out 1 Audio Out 2 Audio Out 1 Audio Out 2 Audio
Out 3
Analogue Off Off Loudspeaker mono VCR Loudspeaker mono Aux VCR
Analogue Off On Loudspeaker L Loudspeaker R Loudspeaker L Loudspeaker R VCR
Analogue On Off Loudspeaker mono VCR Loudspeaker mono VCR L VCR R
Analogue On On Loudspeaker L Loudspeaker R Loudspeaker L Loudspeaker R VCR
SPDIF Off Off Loudspeaker mono VCR Loudspeaker mono Aux VCR
SPDIF Off On Loudspeaker L & R VCR Loudspeaker L & R Aux VCR
SPDIF On Off Loudspeaker mono VCR Loudspeaker mono VCR L VCR R
SPDIF On On Loudspeaker L & R VCR Loudspeaker L & R VCR L VCR R
Out 1 mode is controlled through the xconfiguration audio outputs line type command (overleaf)
Audio StereoSpeakers:
Turns stereo speakers On or Off.
Example: xconfiguration audio stereospeakers: on
Audio VCRDucking:
If VCR Ducking is set to On, the VCR audio level will be attenuated if someone talks into the microphone or at the far end.
Example: xconfiguration audio vcrducking: on
Audio KeyTones:
If set to On there will be a sound indicator when pressing keys on the remote control.
Example: xconfiguration audio keytones: on
Audio Inputs Microphone [1..x]
6000 MXP: x=3
3000 MXP: x=2 Level: <1..16>
Defines the input levels for the different microphones.
Example: xconfiguration audio inputs microphone 2 level: 10
By default, all inputs are
enabled. Just plug in an audio
source and it is active. Audio
inputs that are On will auto-
matically be mixed. Unconnected
inputs will automatically be
muted. Select Off to prevent
audio/noise from connected but
unused inputs.
The microphone inputs are
intended for electret type micro-
phones. The microphone inputs
are balanced with 24 V phantom
power.
Audio Inputs Microphone [1..x]
6000 MXP: x=3
3000 MXP: x=2 Mode:
Turns On or Off the different microphone inputs.
Example: xconfiguration audio inputs microphone 2 mode: off
Turns microphone 2 off.
Audio Inputs Microphone [1..x]
6000 MXP: x=3
3000 MXP: x=2 Mode:
NOTE! Applies to 6000 MXP only! Here the Microphone 3 Mode can be set to Line. It then
becomes a balanced line level input. The gain will be reduced accordingly.
Example: xconfiguration audio inputs microphone 3 mode: line
Sets microphone input 3 on a 6000 MXP to a balanced line level input.
Audio Inputs Line [1..x]
6000 MXP: x=3
3000 MXP: x=2 Level: <1..16>
Defines the input levels for the different line inputs.
Example: xconfiguration audio inputs line 2 level: 10
Audio
cont...