Programming, 3 list of programming items – Omega RD200 User Manual
Page 39
-35-
7. PROGRAMMING
7.3 List of Programming Items
Parameters
Key operations
Programming
items
Defaults
Programming ranges
Ref.
page
Alarm dead
band
+
(3 sec. or more)
-
0.1
0.1 to 9.9 (%): % programming of scale
span
11.6
Start time
Not
programmed
00:00 to 23:59
Periodic
data printing
+
Interval time
Not
programmed
00H05* to 23H59 *Limited by chart speed.
11.7
Engineering
unit *
+
-
V
Max. 5 digits
(Including numeric values, alphabetic
characters, %, /,
°C, °F and space)
Reflected by “Range No.” programmed
(mV, V,
°C, k)
11.8
Tag *
+
-
Not
programmed
Max. 9 digits (Including numeric values,
alphabetic characters, %, /,
°C, °F and
space)
11.9
No.
Not
programmed
1 to 5, Five kinds of messages can be
programmed.
Message
+
(3 sec. or more)
Message
Not
programmed
Max. 15 digits
(Including numeric values, alphabetic
characters, %, /,
°C, °F and space)
11.10
Burnout *
+
(3 sec. or more)
-
non
non, UP bUrn, doWn bUrn
For channels with voltage range, burnout
is disabled (“non”), even if burnout is
programmed (up or down).
11.11
Pass code
non
non (not programmed). For programming,
use 4 digits from 0 to 9.
Passcode/
keylock
+
(3 sec. or more)
Key lock
UnLoCkEd
LockEd, UnLoCkEd
11.12
Time axis
synchronization
+
(3 sec. or more)
-
oFF on,
oFF
9.6
Input filter*
+
(3 sec. or more)
Time
constant
0
0, 0 to 10 (sec.). “0” means no time
constant.
11.13
Copy
+
Programming in each
programming mode
-
-
Programmed parameters can be copied to
other channels. Available parameters to be
copied are [Range/Printing range],
[Engineering unit] and [Tag].
11.14
* Programming is required to each channel. For 1-pen type, programming is only for CH 1. The items without *
mark are programming common to all channels. For "alarm", programming is required to each level of
channels.
3
Programming for Options
Parameters
Programming
items
Key operations
Programming
contents
Defaults
Programming ranges
Ref.
page
Relay
No.
+ Relay
No.
0
"0" to "n" (n: 6, 12)*
In alarm programming mode,
program relay Nos. (terminal
Nos.) for alarm output.
* number of output points
AND/
OR
+
(3 sec. or more)
AND/OR or
AND/OR programming is required
for each relay No.
Relay coil
E
E (energize), d (not energize)
Relay output
U
H (hold), U (not hold)
Alarm
output
Output
mode
+
(3 sec. or more)
Alarm display
U
H (hold), U (not hold)
Common
to all relay
Nos.
12.1
SHIFT
SHIFT
SHIFT
SHIFT
0
CLEAR
0
CLEAR
0
CLEAR
5
DATA I
3
UNIT
6
A - Z
/
9
LIST
8
ALARM
°C
SHIFT
SPACE
COPY(=)
SHIFT
8
ALARM
DISP
°C
°C
0
CLEAR
SHIFT
6
A - Z
SHIFT
%