Table 78. transceiver dc characteristics, Table 79. transceiver ac characteristics – ST & T UPSD3212C User Manual
Page 84
uPSD3212A, uPSD3212C, uPSD3212CV
84/163
Table 78. Transceiver DC Characteristics
Note: 1. V
CC
= 5V ± 10%; V
SS
= 0V; T
A
= 0 to 70°C.
2. Level guaranteed for range of V
CC
= 4.5V to 5.5V.
3. With RPU, external idle resistor, 7.5
κ
±2%, D- to V
CC
.
Table 79. Transceiver AC Characteristics
Note: 1. V
CC
= 5V ± 10%; V
SS
= 0V; T
A
= 0 to 70°C.
2. Level guaranteed for range of V
CC
= 4.5V to 5.5V.
3. With RPU, external idle resistor, 7.5
κ
±2%, D- to V
CC
.
4. C
L
of 50pF(75ns) to 350pF (300ns).
5. Measured at crossover point of differential data signals.
6. USB specification indicates 330ns.
Symb
Parameter
Test Conditions
(1)
Min
Max
Unit
V
OH
Static Output High
15k
Ω
± 5% to GND
(2,3)
2.8
3.6
V
V
OL
Static Output Low
Notes 2, 3
—
0.3
V
V
DI
Differential Input Sensitivity
|(D+) - (D-)|,
0.2
—
V
V
CM
Differential Input Common Mode
0.8
2.5
V
V
SE
Single Ended Receiver Threshold
—
0.8
2.0
V
C
IN
Transceiver Capacitance
—
—
20
pF
I
IO
Data Line (D+, D-) Leakage
0V < (D+,D-) < 3.3
–10
10
µA
R
PU
External Bus Pull-up Resistance, D-
7.5k
Ω
± 2% to V
CC
7.35
7.65
k
Ω
R
PD
External Bus Pull-down Resistance
15k
Ω
± 5%
14.25
15.75
k
Ω
Symb
Parameter
Test Conditions
(1)
Min
Max
Unit
tDRATE
Low Speed Data Rate
Ave. bit rate (1.5Mb/s ± 1.5%)
1.4775
1.5225
Mbit/s
tDJR1
Receiver Data Jitter Tolerance
To next transition,
(5)
–75
75
ns
tDJR2
Differential Input Sensitivity
For paired transition,
(5)
–45
45
ns
tDEOP
Differential to EOP Transition Skew
(5)
–40
100
ns
tEOPR1
EOP Width at Receiver
Rejects as EOP
(5,6)
165
—
ns
tEOPR2
EOP Width at Receiver
Accepts as EOP
(5)
675
—
ns
tEOPT
Source EOP Width
—
–1.25
1.50
µs
tUDJ1
Differential Driver Jitter
To next transition,
–95
95
ns
tUDJ2
Differential Driver Jitter
To paired transition,
–150
150
ns
tR
USB Data Transition Rise Time
Notes 2, 3, 4
75
300
ns
tF
USB Data Transition Fall Time
Notes 2, 3, 4
75
300
ns
tRFM
Rise/Fall Time Matching
t
R
/ t
F
80
120
%
VCRS
Output Signal Crossover Volt age
—
1.3
2.0
V