HP 30 HP30 - Manual (Page 80)

Chapter 5 - Parameter List
5-20
Keypad Display Setting Range
Code Description
LCD 7-Segment LCD 7-Segment
Units
Factory
Default
Adj.
During
Run
Page
APP-02 27 Traverse Amplitude Trv. Amp 02 0.0 to 20.0 [%] 0.1 0.0 [%] Yes 6-2
APP-03
Traverse Scramble
Amplitude
Trv. Scr 03 0.0 to 50.0 [%] 0.1 0.0 [%] Yes 6-2
APP-04 Traverse Accel Time
Trv Acc Time 04 0 to 6000 [sec] 0.1 2.0 [sec] Yes 6-2
APP-05 Traverse Decel Time
Trv Dec Time 05 0 to 6000 [sec] 0.1 3.0 [sec] Yes 6-2
APP-06
Traverse Offset (Hi)
Setting
Trv Off Hi 06 0.0 to 20.0 [%] 0.1 0.0 [%] Yes 6-2
APP-07
Traverse Offset (Lo)
Setting
Trv Off Lo 07 0.0 to 20.0 [%] 0.1 0.0 [%] Yes 6-2
APP-08 28
Running Auxiliary Motor
Number Display
Aux Mot Run 08 - - - - 6-2
APP-09
Starting Aux. Motor
Selection
Starting Aux 09 1 to 4 1 1 Yes 6-2
APP-10
Operation Time Display
on Auto Change
Auto Op Time 10 - - - - 6-2
APP-11
Start Frequency of Aux.
Motor 1
Start freq 1 11 0 to FU1-20 0.01 49.99 [Hz] Yes
APP-12
Start Frequency of Aux.
Motor 2
Start freq 2 12 0 to FU1-20 0.01 49.99 [Hz] Yes
APP-13
Start Frequency of Aux.
Motor 3
Start freq 3 13 0 to FU1-20 0.01 49.99 [Hz] Yes
APP-14
Start Frequency of Aux.
Motor 4
Start freq 4 14 0 to FU1-20 0.01 49.99 [Hz] Yes
6-2
APP-15
Stop Frequency of Aux.
Motor 1
Stop freq 1 15 0 to FU1-20 0.01 15.00 [Hz] Yes
APP-16
Stop Frequency of Aux.
Motor 2
Stop freq 2 16 0 to FU1-20 0.01 15.00 [Hz] Yes
APP-17
Stop Frequency of Aux.
Motor 3
Stop freq 3 17 0 to FU1-20 0.01 15.00 [Hz]] Yes
APP-18
Stop Frequency of Aux.
Motor 4
Stop freq 4 18 0 to FU1-20 0.01 15.00 [Hz] Yes
6-2
APP-19
Delay Time before
Operating Aux Motor
Aux start DT 19 0 to 9999 [sec] 0.1 60.0 [sec] Yes
APP-20
Delay Time before
Stopping Aux Motor
Aux stop DT 20 0 to 9999 [sec] 0.1 60.0 [sec] Yes
6-2
APP-21 The Number of Aux Motor
Nbr Aux’s 21 0 to 4 1 4 Yes 6-2
No 0
APP-22 PID Bypass Selection
Regul Bypass 22
Yes 1
- No Yes 6-2
APP-23 Sleep Delay Time
Sleep Delay 23 0 to 9999 [sec] 0.1 60.0 [sec] Yes 6-2
APP-24 Sleep Frequency
Sleep Freq 24 0 to FU1-20 0.01 19.00 [Hz] Yes 6-2
27 Code APP-02 through APP-07 appears only when APP-01 is set to ‘Traverse’.
28 Code APP-08 through APP-31 appears only when APP-01 is set to ‘MMC’.