HP 30 HP30 - Manual (Page 66)

Chapter 5 - Parameter List
5-6
5.3 Function 2 Group [FU2]
Keypad Display Setting Range
Code Description
LCD 7-Segment LCD 7-Segment
Units
Factory
Default
Adj.
During
Run
Page
FU2-00 Jump to desired code # Jump code Not displayed 1 to 94 Not available 1 1 Yes 6-2
FU2-01 Previous Fault History 1 Last trip-1 01
FU2-02 Previous Fault History 2 Last trip-2 02
FU2-03 Previous Fault History 3 Last trip-3 03
FU2-04 Previous Fault History 4 Last trip-4 04
FU2-05 Previous Fault History 5 Last trip-5 05
By pressing [PROG] and [▲] key,
the frequency, current, and
operational status at the time of fault
can be seen.
- None -
No 0
FU2-06 Erase Fault History Erase trips 06
Yes 1
- No Yes
6-2
FU2-07 Dwell Frequency Dwell freq 07 FU1-22 to FU1-20 0.01 5.00 [Hz] No
FU2-08 Dwell Time Dwell time 08 0 to 10 [sec] 0.1 0.0 [sec] No
6-2
No 0
FU2-10
Frequency Jump
Selection
Jump freq 10
Yes 1
- No No
FU2-11 17 Jump Frequency 1 Low Jump lo 1 11 FU1-22 to FU2-12 0.01 10.00 [Hz] No
FU2-12 Jump Frequency 1 High Jump Hi 1 12 FU2-11 to FU1-20 0.01 15.00 [Hz] No
FU2-13 Jump Frequency 2 Low Jump lo 2 13 FU1-22 to FU2-14 0.01 20.00 [Hz] No
FU2-14 Jump Frequency 2 High Jump Hi 2 14 FU2-13 to FU1-20 0.01 25.00 [Hz] No
FU2-15 Jump Frequency 3 Low Jump lo 3 15 FU1-22 to FU2-16 0.01 30.00 [Hz] No
FU2-16 Jump Frequency 3 High Jump Hi 3 16 FU2-15 to FU1-20 0.01 35.00 [Hz] No
6-2
FU2-17
Start Curve for S-Curve
Accel/Dedel Pattern
Start Curve 17 1 to 100 [%] 1 40% No
FU2-18
End Curve for S-Curve
Accel/Dedel Pattern
End Curve 18 1 to 100 [%] 1 40% No
6-2
FU2-19
Input/Output Phase Loss
Protection
Trip select 19
00 to 11
(Bit Set)
- 00 Yes 6-2
No 0
FU2-20 Power ON Start Selection Power-on run 20
Yes 1
- No Yes 6-2
No 0
FU2-21 Restart after Fault Reset RST restart 21
Yes 1
- No Yes 6-2
FU2-22 Speed Search Selection Speed Search 22
0000 to 1111
(Bit Set)
- 0000 No
FU2-23
Current Limit Level
During Speed Search
SS Sup-Curr 23 80 to 200 [%] 1 100 [%] Yes
FU2-24
P Gain
During Speed Search
SS P-gain 24 0 to 30000 1 100 Yes
FU2-25
I Gain
During speed search
SS I-gain 25 0 to 30000 1 1000 Yes
6-2
FU2-26
Number of Auto Restart
Attempt
Retry number 26 0 to 10 1 0 Yes 6-2
17 Code FU2-11 through FU2-16 appears only when FU2-10 is set to ‘Yes’.