DMP Electronics DMP Command Processor Panel XR500 - Manual (Page 26)

XR500 Series Canadian Programming Guide Digital Monitoring Products
17
DEVICE SETUP
If you do not enter any area numbers, all users with Door Access authority receives a
door access without regard to schedules. If the user code is programmed for Anti-Pass
YES, then the user is logged into all matching areas. This user is not allowed to access
these areas again until they have egressed the area. See Egress Areas.
When all areas accessed by a door are armed, the door is locked by the panel.
Note: For an All/Perimeter, Home/Sleep/Away, or Home/Sleep/Away with Guest
system, Access Areas should be left at factory default settings.
6.7 Egress Areas
Press the COMMAND key to program Egress Areas. To select an area, enter the area
number using the digit keys on the keypad. When an area is selected, an asterisk
appears next to the area number. Enter the number again to deselect the area.
Press COMMAND to display the next set of areas. Refer to the Multiple Displays
section at the beginning of this document.
Note: For an All/Perimeter, Home/Sleep/Away, or Home/Sleep/Away with Guest
system, Egress Areas should be left at factory default settings.
Note: If an area is programmed as an access area, it cannot be programmed as an
egress area and therefore does not display during Egress Areas programming.
Use this option to detect Anti-passback violations. Anti-passback requires a user to
properly exit (egress) an area they have previously accessed. If users fail to exit
through the proper card reader location they are not granted access on their next
attempt. Users must have matching access area numbers assigned to their profile,
to receive a door access at this device. If the user is programmed for Anti-Pass
YES, then the user is logged out of all matching areas. This allows the user to again
access the area. See Access Areas section.
If you do not enter any area numbers, all users with Door Access authority receives a
door access without regard to schedules. If you are not using the Anti-Pass feature
leave Egress Areas blank.
6.8 DISPLAY AREAS: Display Areas
*1 *2 *3 *4
*5 *6 *7 *8
*9 *10 *11 *12
*13 *14 *15 *16
*17 *18 *19 *20
*21 *22 *23 *24
*25 *26 *27 *28
*29 *30 *31 *32
Press the COMMAND key to program Display Areas. To select an area between 1 and
32, enter the area number using the keypad digit keys. When an area is selected, an
asterisk appears next to the area number. Enter the number again to deselect the
area. Press COMMAND to display the next set of areas. Default is all area numbers.
Refer to the Multiple Displays section at the beginning of this document.
Display Areas allows the XR500 Series burglary activities to be segmented so that
only specific area(s) and their associated operation appear at a particular keypad.
Area number(s) selected in this field affect the way users interact with the system
from this particular device. For example: Program Device 1 to show only the zone
activities and armed status of Area 1.
Enter the area number(s) that this keypad is to display. This allows specific area control
from specific keypads, as well as annunciation of zones assigned to those area(s). When
Display Areas is left defaulted (all areas selected), Menu Display and Status List items
determine whether zone alarms and troubles display at this device, regardless of area
assignment. Also, all system areas may be armed and disarmed from this device.
Note: For an All/Perimeter or Home/Sleep/Away system, Display Areas should be
left at factory default settings.
For Home/Sleep/Away with Guest arming systems, the Display Areas selection
determines which system the keypad arms and disarms. With areas 1, 2 or 3 being
the first areas selected, the keypad is assigned to the Main system. With area 4, 5 or 6
being the first areas selected, the keypad is assigned to the Guest 1 system. With area
7, 8 or 9 being the first areas selected, the keypad is assigned to the Guest 2 system.
Keypads can have additional areas assigned for Event Display.
User Action Allowed
When an area(s) is selected, the following user actions are allowed:
• Arming or Disarming of the area(s) selected from the ARM or DISARM menu
• Alarm Silence for the area(s) selected
• Zone Bypass of zones assigned to the area(s) selected
• Zone Monitor of zone assigned to the area(s) selected
• Shift schedule changes allowed for the area(s) selected
• Closing Check Schedule Extend is allowed for the area(s) selected
EGRESS AREAS: