Metrohm 751 GPD Titrino - Manual (Page 174)

3.2 Remote control commands
751 GPD Titrino
171
$Q sends the volume. With the function &Info.Assembly.Counter.Clear $G, the
volume counter is set to zero.
3.2.2. 3.2.2.143. 143. IInfo.A .ActualInfo.A .Assembly.M .Meas read only
$Q sends the current measured value from the assembly.
3.2.2. 3.2.2.144. 144. IInfo.A .ActualInfo.T .Titrator.C .CyclNo read only
IInfo.A .ActualInfo.T .Titrator.V .V read only
IInfo.A .ActualInfo.T .Titrator.M .Meas read only
IInfo.A .ActualInfo.T .Titrator.d .dVdt read only
IInfo.A .ActualInfo.T .Titrator.dM .dMeasdt read only
IInfo.A .ActualInfo.T .Titrator.dMeasdV .dMeasdV read only
IInfo.A .ActualInfo.T .Titrator.E .ERC read only
IInfo.A .ActualInfo.T .Titrator.T .T read only
$Q sends the current values in the following formats:
DET MET SET KFT STAT,
DOC DOS MEAS CAL
CyclNo 127 127 127 127 127 127 127 127
V(ml) 1.2345 1.2345 1.2345 1.2345 1.2345 1.2345 - -
Meas:
pH
U, Ipol (mV)
Upol (uA)
T (°C) 3.345
-345.6
-12.5
- 3.345
-345.6
-12.5
- 3.6(mV)
-345.6
-12.5
- -
-345.6
-12.5
- 3.6(mV)
-345.6
-12.5
- 3.6(mV)
-345.6
-12.5 3.345
-345.6
-12.5
25.0 3.345
-
-
-
dVdt (ul/s) - - 2.5142 2.5142 2.5142 - - -
dMeasdt
pH,U,Ipol mV/s
Upol (uA/s)
T (°C/s) 0.7957
0.7957
- 0.7957
0.7957
- 0.7957
0.7957
- 0.7957
0.7957
- 0.7957
0.7957
- -
-
- 0.7957
0.7957
0.7957 0.7957
-
-
dMeasdV (mV/ul) - - 10.6326 10.6326 10.6326 - - -
ERC 34 - - - - - - -
T (°C) 25.9 25.9 - - 25.9 25.9 25.9 -
NV: Not Valid. If in the signal drift is OFF in modes MEAS and CAL, the signal
drift is NV.
OV will be sent for "overrange".
A time frame can be set up from the cycle number and the cycle time (see
3.2.2.149). The cycle number is set to 0 at the start of a method and it is in-
cremented until the end of the method.
3.2.2. 3.2.2.145. 145. IInfo.A .ActualInfo.M .MeasPt.I.Index read only
IInfo.A .ActualInfo.M .MeasPt.X .X read only
IInfo.A .ActualInfo.M .MeasPt.Y .Y read only
IInfo.A .ActualInfo.M .MeasPt.Z .Z1 read only
IInfo.A .ActualInfo.M .MeasPt.Z2 .Z2 read only
IInfo.A .ActualInfo.E .EP.I.Index read only
IInfo.A .ActualInfo.E .EP.X .X read only
IInfo.A .ActualInfo.E .EP.Y .Y read only