Metrohm 751 GPD Titrino - Manual (Page 156)

3.2 Remote control commands
751 GPD Titrino
153
wait: Interrupt dosing until the limit value is no longer violated, then con-
tinue automatically.
3.2.2. 3.2.2.50. 50. M Mode.P .Parameter.M .Monitoring.L .L10Output.A .AssignOutput
meas, temp, rate, all, none none
M Mode.P .Parameter.M .Monitoring.L .L10Output.L .Limit upper,lower,any any
M Mode.P .Parameter.M .Monitoring.L .L10Output.O .Output active, pulse pulse
Parameters for STAT, DOS, DOC: Output of a signal on L10 output (pin 8) of
the remote socket on limit value violation.
The output can be assigned a definite or all monitoring value(s) as well as the
violated limit and the type of signal to be outputted determined.
3.2.2. 3.2.2.51. 51. M Mode.P .Parameter.P .Presel.R .RateDisp ON, OFF OFF
Parameters for STAT, DOC: Display of the current rate during the determination.
3.2.2. 3.2.2.52. 52. M Mode.P .Parameter.D .DosPara.T .Type volume volume, time, rate
M Mode.P .Parameter.D .DosPara.V .Volume.V .Volume 0.000...10 10...99999.99
M Mode.P .Parameter.D .DosPara.V .Volume.D .DisType time, rate rate
M Mode.P .Parameter.D .DosPara.V .Volume.R .Rate 0.001...150, max. max.
M Mode.P .Parameter.D .DosPara.V .Volume.T .Time 1...100 100...999 999
M Mode.P .Parameter.D .DosPara.Ti .Time.T .Time 1...100 100...999 999
M Mode.P .Parameter.D .DosPara.Ti .Time.D .DisType volume volume, rate
M Mode.P .Parameter.D .DosPara.Ti .Time.R .Rate 0.001...150, max. max.
M Mode.P .Parameter.D .DosPara.Ti .Time.V .Volume 0.000...10 10...99999.99
M Mode.P .Parameter.D .DosPara.R .Rate.R .Rate 0.001...150, max. max.
M Mode.P .Parameter.D .DosPara.R .Rate.S .StopType volume volume, time
M Mode.P .Parameter.D .DosPara.R .Rate.T .Time 1...100 100...999 999
M Mode.P .Parameter.D .DosPara.R .Rate.V .Volume 0.000...10 10...99999.99
Parameters for DOS: In the equation Rate = Volume/Time, two parameters are
preset, the third is calculated. Depending on the entry of the type, the following
information is required: .Volume, .Time or .Rate.
Entries: .Volume in ml, .Time in s, .Rate in ml/min.
3.2.2. 3.2.2.53. 53. M Mode.P .Parameter.D .DosPara.P .Pause 00...999 999
Parameters for DOS: Pause time in s.
3.2.2. 3.2.2.54. 54. M Mode.P .Parameter.D .DosPara.TD .TDelta 1...10 10...999 999
Parameters for DOS, DOC: Time interval for the entry of a measured point in the
list of measured points.
3.2.2. 3.2.2.55. 55. M Mode.P .Parameter.D .DosPara.Te .Temp -170.0...25.0 25.0...500.0
Parameters for DOS, DOC: Temperature in °C. The temperature is measured
continuously and updated if a T sensor is attached.
The temperature is used for temperature compensation in pH measurements.