Brocade Multi-Service IronWare Security Configuration Guide (Supporting R05.6.00) - Manual (Page 243)

Multi-Service IronWare Security Configuration Guide 225
53-1003035-02
IPv6 receive ACLs
4
SYSLOG: <14>Jun 6 10:38:14 FWD14 IPv6-rACL: Activated by operator from console
session.
4. ipv6 receive delete-acl-all
SYSLOG: <13>Jun 6 10:39:45 FWD14 IPv6-rACL: Deleting IPv6 Receive ACLs.
5. IPv6 rACL CAM partition exhaust error (this unbinds rACL from the interface module)
SYSLOG: <9>May 10 10:17:48 IxANVL-14 CAM IPv6 Receive ACL partition warning: total
1024 (reserved 0), free 0, slot 3, ppcr 0
SYSLOG: <13>Jun 1 07:15:10 IxANVL-1 IPv6-RACL: Port 3/1, IPv6 Receive ACL b1
exceed configured CAM size, larger partition size required.
SYSLOG: <13>Jun 1 07:15:10 IxANVL-1 IPv6-RACL: Unbinding IPv6 Receive ACL b1
6. Policy-map limit exhaust error (this unbinds rACL from the interface module).
SYSLOG: <13>Jun 1 07:15:10 IxANVL-1 IPv6-RACL: Port 3/1, IPv6 Receive ACL b1
exceed configured RL class limit.
SYSLOG: <13>Jun 1 07:15:10 IxANVL-1 IPv6-RACL: Unbinding IPv6 Receive ACL b1
7. CAM malloc error (this unbinds rACL from the interface module).
SYSLOG: <13>Jun 1 07:15:10 IxANVL-1 IPv6-RACL: Port 3/1, IPv6 Receive ACL b1 CAM
malloc error.
SYSLOG: <13>Jun 1 07:15:10 IxANVL-1 IPv6-RACL: Unbinding IPv6 Receive ACL b1
Displaying accounting information for IPv6 rACLs
Before you can collect ACL accounting statistics, you must enable accounting for IPv6 rACL. Refer to
“ACL accounting” on page 213 for further information on how to enable accounting using the
enable-acl-counter command.
To display rACL accounting information for the named ACL “b1“, enter the following command
Syntax: show ipv6 access-list receive accounting {brief | name acl-name}
The brief parameter displays IPv6 rACL accounting information in brief. The name acl-name
variable specifies the name of a receive access-control list. The maximum name length is 256
characters.
To clear IPv6 rACL accounting information for an ACL named “acl_ext1”, use the following
command.
Brocade(config)# clear ipv6 access-list receive name acl_ext1
To clear accounting statistics for all configured IPv6 rACLs, enter the following command.
Brocade(config)# clear ipv6 access-list receive all
Brocade(config)# show ipv6 access-list receive accounting name b1
IPv6 Receive ACL Accounting Information:
IPv6 Receive ACL b1
ACL hit count for software processing (accum) 0
HW counters:
0: permit tcp any host 2000::2
Hit count: (1 sec) 0 (1 min) 0
(5 min) 0 (accum) 0
1: permit udp any host 1000::1
Hit count: (1 sec) 0 (1 min) 0
(5 min) 0 (accum) 0