Brocade FastIron SX, FCX, and ICX Diagnostic Reference User Manual
Page 61

Brocade FastIron SX, FCX, and ICX Diagnostic Reference
49
53-1003076-02
VXLAN debug commands
3
debug l2-tunnel vxlan tunnel all
Syntax: [no] debug l2-tunnel vxlan tunnel all
This command enables debug of all flows of a VXLAN tunnel creation, updation, and deletion.
Command output resembles the following example.
Brocade# debug l2-tunnel vxlan tunnel all
[VXLAN]: L2-tunnel 1 - next hop 0.0.0.0 is not router dest - update Tunnel
[VXLAN]: Update 2 all maps on L2-tunnel 1
[VXLAN]: Success to update all maps on L2-tunnel 1[VXLAN]: Create vxlan tables for
L2-tunnel 1
[VXLAN]: Create L3 intf 65535 for L2-tunnel 1
[VXLAN]: Reusing L3 intf 6096 for L2-tunnel 1 with exising L3 intf 65535 which
reused from L2-tunnel 65535
[VXLAN]: Success to create L3 intf 6096 for L2-tunnel 1
[VXLAN]: Create vxlan egress ip tunnel for L2-tunnel 1 with index ffffffff
[VXLAN]: Success to create vxlan egress ip tunnel for L2-tunnel 1 with index
4c000002
[VXLAN]: Create Forward nextHop 65535 for L2-tunnel 1 on network port 1/1/2
[VXLAN]: Success to reuse Forward nexthop 66 for L2-tunnel 1 from L2-tunnel 2 on
network port 1/1/2
[VXLAN]: Create vxlan terminator for L2-tunnel 1
[VXLAN]: Fail to get vxlan terminator on device 0 : Entry not found
[VXLAN]: Success to create vxlan terminator for L2-tunnel 1
[VXLAN]: Success to create vxlan tables for L2-tunnel 1
[VXLAN]: Update 1 all maps on L2-tunnel 1
[VXLAN]: Success to update all maps on L2-tunnel 1
[VXLAN]: bring tunnel id 1 up
[VXLAN]: Create tunnel id 1 with next hop 64 - old next hop is 4
debug l2-tunnel vxlan tunnel sw-prog
Syntax: [no] debug l2-tunnel vxlan tunnel sw-prog
This command enables debug of software programming flows of VXLAN tunnel creation, updation,
and deletion. Command output resembles the following example.
Brocade# debug l2-tunnel vxlan tunnel sw-prog
[VXLAN]: L2-tunnel 1 - next hop 0.0.0.0 is not router dest - update Tunnel
[VXLAN]: Update 2 all maps on L2-tunnel 1
[VXLAN]: Success to update all maps on L2-tunnel 1
[VXLAN]: Update 1 all maps on L2-tunnel 1
[VXLAN]: Success to update all maps on L2-tunnel 1
[VXLAN]: bring tunnel id 1 up
[VXLAN]: Create tunnel id 1 with next hop 64 - old next hop is 4
debug l2-tunnel vxlan tunnel hw-prog
Syntax: [no] debug l2-tunnel vxlan tunnel hw-prog
This command enables debug of hardware programming flows of VXLAN tunnel creation, updation,
and deletion. Command output resembles the following example.
Brocade# debug l2-tunnel vxlan tunnel hw-prog
[VXLAN]: Create vxlan tables for L2-tunnel 2
[VXLAN]: Create L3 intf 65535 for L2-tunnel 2
[VXLAN]: Reusing L3 intf 6096 for L2-tunnel 2 with exising L3 intf 65535 which
reused from L2-tunnel 65535
[VXLAN]: Success to create L3 intf 6096 for L2-tunnel 2