Brocade FastIron SX, FCX, and ICX Diagnostic Reference User Manual
Page 150
138
Brocade FastIron SX, FCX, and ICX Diagnostic Reference
53-1003076-02
IGMP debug commands
6
IGMP: rcvd Report-V2(t=22) g=239.0.1.53 resp=100, pkt S=10.17.17.222 to
239.0.1.53, on v17 (phy 2/1/17), igmp_size=8
IGMP: rcvd Report-V2(t=22) g=239.0.1.54 resp=100, pkt S=10.17.17.222 to
239.0.1.54, on v17 (phy 2/1/17), igmp_size=8
IGMP: rcvd Report-V2(t=22) g=239.0.1.55 resp=100, pkt S=10.17.17.222 to
239.0.1.55, on v17 (phy 2/1/17), igmp_size=8
IGMP: rcvd Report-V2(t=22) g=239.0.1.56 resp=100, pkt S=10.17.17.222 to
239.0.1.56, on v17 (phy 2/1/17), igmp_size=8
aIGMP: rcvd Report-V2(t=22) g=239.0.1.57 resp=100, pkt S=10.17.17.222 to
239.0.1.57, on v17 (phy 2/1/17), igmp_size=8
IGMP: rcvd Report-V2(t=22) g=239.0.1.58 resp=100, pkt S=10.17.17.222 to
239.0.1.58, on v17 (phy 2/1/17), igmp_size=8
lIGMP: rcvd Report-V2(t=22) g=239.0.1.59 resp=100, pkt S=10.17.17.222 to
239.0.1.59, on v17 (phy 2/1/17), igmp_size=8
IGMP: rcvd Report-V2(t=22) g=239.0.1.60 resp=100, pkt S=10.17.17.222 to
239.0.1.60, on v17 (phy 2/1/17), igmp_size=8
IGMP: rcvd Report-V2(t=22) g=239.0.1.61 resp=100, pkt S=10.17.17.222 to
239.0.1.61, on v17 (phy 2/1/17), igmp_size=8
lIGMP: rcvd Report-V2(t=22) g=239.0.1.62 resp=100, pkt S=10.17.17.222 to
239.0.1.62, on v17 (phy 2/1/17), igmp_size=8
IGMP: rcvd Report-V2(t=22) g=239.0.1.63 resp=100, pkt S=10.17.17.222 to
239.0.1.63, on v17 (phy 2/1/17), igmp_size=8
IGMP: rcvd Report-V2(t=22) g=239.0.1.64 resp=100, pkt S=10.17.17.222 to
239.0.1.64, on v17 (phy 2/1/17), igmp_size=8
IGMP: rcvd Report-V2(t=22) g=239.0.1.65 resp=100, pkt S=10.17.17.222 to
239.0.1.65, on v17 (phy 2/1/17), igmp_size=8
IGMP: rcvd Report-V2(t=22) g=239.0.1.66 resp=100, pkt S=10.17.17.222 to
239.0.1.66, on v17 (phy 2/1/17), igmp_size=8
Debug message destination: default (console)
All possible debuggings have been turned off
tracking is off and all results are cleared
Turn off stack trace of write table
Disable shadow register write will disable all writes from shadow to hardware
debug ip igmp clear
Syntax: [no] debug ip igmp clear
This command clears all the IGMP debug settings.
Brocade# debug ip igmp clear
no debug ip igmp is enabled
debug ip igmp down-port
Syntax: [no] debug ip igmp down-port
This command monitors the port that is down.
Brocade# debug ip igmp down-port
Brocade# debug ip igmp show
igmp debug-enable-any = 1
debug ip igmp port-down is enabled
Brocade# debug ip igmp
Brocade# IGMP: rcvd Report-V2(t=22) g=239.0.0.84 resp=100, pkt S=10.17.17.222 to
239.0.0.84, on v17 (phy 2/1/17), igmp_size=8
IGMP: rcvd Report-V2(t=22) g=239.0.0.85 resp=100, pkt S=10.17.17.222 to
239.0.0.85, on v17 (phy 2/1/17), igmp_size=8
IGMP: rcvd Report-V2(t=22) g=239.0.0.86 resp=100, pkt S=10.17.17.222 to
239.0.0.86, on v17 (phy 2/1/17), igmp_size=8