Brocade FastIron SX, FCX, and ICX Diagnostic Reference - Manual (Page 163)

Brocade FastIron SX, FCX, and ICX Diagnostic Reference 151
53-1003076-02
IGMP debug commands
6
This command displays debugging information related to the IGMP proxy packets as shown in the
following example.
Brocade# debug ip igmp proxy packet
Debug: Jan 1 20:55:28 20:55:46 - MCPROXY_TX: [IPv4:default-vrf] sending v1v2 grp
229.2.1.1 rprt to vir port v85 phy port 2/13
Debug: Jan 1 20:55:28 20:55:46 - MCPROXY_TX: [IPv4:default-vrf] receive group
query 229.2.1.1 on port e2/13 max resp code 10
Debug: Jan 1 20:55:29 20:55:47 - MCPROXY_TX: [IPv4:default-vrf] receive group
query 229.2.1.1 on port e2/13 max resp code 10
Debug: Jan 1 20:55:40 20:55:58 - MCPROXY_TX: [IPv4:default-vrf] sending v1v2 grp
229.2.1.1 rprt to vir port v85 phy port 2/13
Debug: Jan 1 20:55:42 20:55:59 - MCPROXY_TX: [IPv4:default-vrf] sending v1v2 grp
229.2.1.1 rprt to vir port v85 phy port 2/13
debug ip igmp proxy rx
Syntax: [no] debug ip igmp proxy rx
This command displays the IGMP proxy packets received as shown in the following example.
Brocade# debug ip igmp proxy rx
debug ip igmp proxy Debug: Jan 1 20:58:06 20:58:23 - MCPROXY_RX:
[IPv4:default-vrf] receive general query on port e2/13 max resp code 100
Debug: Jan 1 21:00:11 21:0:28 - MCPROXY_RX: [IPv4:default-vrf] receive general
query on port e2/13 max resp code 100
Debug: Jan 1 21:04:21 21:4:38 - MCPROXY_RX: [IPv4:default-vrf] receive general
query on port e2/13 max resp code 100
Debug: Jan 1 21:06:26 21:6:43 - MCPROXY_RX: [IPv4:default-vrf] receive general
query on port e2/13 max resp code 100
Debug: Jan 1 21:08:31 21:8:48 - MCPROXY_RX: [IPv4:default-vrf] receive general
query on port e2/13 max resp code 100
Debug: Jan 1 21:10:36 21:10:54 - MCPROXY_RX: [IPv4:default-vrf] receive general
query on port e2/13 max resp code 100
Debug: Jan 1 21:12:41 21:12:59 - MCPROXY_RX: [IPv4:default-vrf] receive general
query on port e2/13 max resp code 100
debug ip igmp proxy show
Syntax: [no] debug ip igmp proxy show
This command displays the IGMP proxy debug settings as shown in the following example.
Brocade# debug ip igmp proxy show
Mcast Proxy debug for IPv4:
Receive debug is enable
Transmit debug is enable
Error debug is enable
debug ip igmp proxy tx
Syntax: [no] debug ip igmp proxy tx
This command displays the IGMP proxy packets transmitted as shown in the following example.
Brocade# debug ip igmp proxy tx
Debug: Jan 1 20:55:28 20:55:46 - MCPROXY_TX: [IPv4:default-vrf] receive group
query 229.2.1.1 on port e2/13 max resp code 10
Debug: Jan 1 20:55:29 20:55:47 - MCPROXY_TX: [IPv4:default-vrf] receive group
query 229.2.1.1 on port e2/13 max resp code 10