Brocade FastIron SX, FCX, and ICX Diagnostic Reference - Manual (Page 175)

Brocade FastIron SX, FCX, and ICX Diagnostic Reference 163
53-1003076-02
PIM debug commands
6
VRF0 Flow Entry Delete (10.0.0.168 232.0.0.36) HW bits: 0 0
VRF0 Flow Entry Delete (10.0.0.168 232.0.0.37) HW bits: 0 0
VRF0 Flow Entry Delete (10.0.0.168 232.0.0.38) HW bits: 0 0
VRF0 Flow Entry Delete (10.0.0.168 232.0.0.39) HW bits: 0 0
VRF0 Flow Entry Delete (10.0.0.168 232.0.0.40) HW bits: 0 0
debug ip pim packet
Syntax: [no] debug ip pim packet source_address group_address [rate]
• source_address - Specifies the source address of the PIM packet
• group_address - Specifies the group address of the PIM packet.
• rate - Specifies the hardware rate.
This command displays debugging information about the PIM packets. Command output
resembles the following example.
Brocade# debug ip pim packet 10.0.0.178 232.0.0.25
debug packet S=10.0.0.178 G=232.0.0.25
Brocade# VRF0 Flow Entry Delete (10.0.0.178 232.0.0.25) HW bits: 1 1
Brocade# debug ip pim packet 10.0.0.178 232.0.0.25 10
debug packet S=10.0.0.178 G=232.0.0.25 rate 10
Brocade# VRF0 Flow Entry Delete (10.0.0.178 232.0.0.25) HW bits: 0 0
VRF0 Flow Entry Delete (10.0.0.178 232.0.0.25) HW bits: 0 0
debug ip pim physical-port ethernet
Syntax: [no] debug ip pim physical-port ethernet stackid/slot/port
This command displays information of the PIM physical ports that are connected. The
stackid/slot/port variable refers to the stack ID, slot number, and port number.
Brocade# debug ip pim physical-port ethernet 2/1/5
Brocade# IGMP: IGMP: rcvd Report-V3(t=34) #rec=1, pkt S=10.2.1.6 to 224.0.0.22, on
v800 (phy 2
/1/5), igmp_size=16
IGMP: IGMP: rcvd Report-V3(t=34) #rec=1, pkt S=10.2.1.6 to 224.0.0.22, on v800
(phy 2/1/5), igmp_size=16
debug ip pim regproc
Syntax: [no] debug ip pim regproc
This command controls register processing and the command output resembles the following
example.
Brocade# debug ip pim regproc
Brocade(config-if-e1000-1/1/11)# debug ip pim regproc
PIM: regproc debugging is on
Brocade(config-if-e1000-1/1/11)# enable
Brocade(config-if-e1000-1/1/11)# PIMSM-REG.VRF0: (10.0.0.168 228.0.0.1) Sending
L2-Null Reg on iface v78
PIMSM-REG.VRF0: (10.0.0.168 228.0.0.2) Sending L2-Null Reg on iface v78
PIMSM-REG.VRF0: (10.0.0.168 228.0.0.3) Sending L2-Null Reg on iface v78
PIMSM-REG.VRF0: (10.0.0.168 228.0.0.4) Sending L2-Null Reg on iface v78
PIMSM-REG.VRF0: (10.0.0.168 228.0.0.5) Sending L2-Null Reg on iface v78
PIMSM-REG.VRF0: (10.0.0.168 228.0.0.6) Sending L2-Null Reg on iface v78
PIMSM-REG.VRF0: (10.0.0.168 228.0.0.7) Sending L2-Null Reg on iface v78
PIMSM-REG.VRF0: (10.0.0.168 228.0.0.8) Sending L2-Null Reg on iface v78