Brocade FastIron SX, FCX, and ICX Diagnostic Reference - Manual (Page 121)

Brocade FastIron SX, FCX, and ICX Diagnostic Reference 109
53-1003076-02
IPv6 OSPF debug commands
5
Debug: Jan 1 19:06:19 OSPFv3: Rcv DbDesc on ve 9 OSPFv3:
(fe80::224:38ff:fed6:7800->OSPFv3: fe80::224:38ff:fe21:6400)
Debug: Jan 1 19:06:19 Option:00-00-13, Bits:00 SEQ:aa922
Debug: Jan 1 19:06:19 OSPFv3: Snd DbDesc on ve 9 OSPFv3:
(fe80::224:38ff:fe21:6400->OSPFv3: fe80::224:38ff:fed6:7800)
Debug: Jan 1 19:06:19 Option:00-00-13, Bits:01 SEQ:aa923
Debug: Jan 1 19:06:19 OSPFv3: Rcv DbDesc on ve 9 OSPFv3:
(fe80::224:38ff:fed6:7800->OSPFv3: fe80::224:38ff:fe21:6400)
Debug: Jan 1 19:06:19 Option:00-00-13, Bits:00 SEQ:aa923
debug ipv6 ospf packet-hello
Syntax: [no] debug ipv6 ospf packet-hello
This command displays all OSPFv3 hello packets in rx or tx mode as shown in the following
example.
Brocade# debug ipv6 ospf packet-hello
OSPFv3: packet-hello debugging is on
Brocade(config-ospf6-router)# Debug: Jan 1 18:52:05 OSPFv3: Snd Hello on ve 9
OSPFv3: (fe80::224:38ff:fe21:6400->OSPFv3: ff02::5)
RtrID:10.4.4.8 DR:10.4.4.8 BDR:10.2.2.2
Debug: Jan 1 18:52:07 OSPFv3: Rcv Hello on ve 9 OSPFv3:
(fe80::224:38ff:fed6:7800->OSPFv3: ff02::5)
RtrID:10.2.2.2 DR:10.4.4.8 BDR:10.2.2.2
Debug: Jan 1 18:52:07 OSPFv3: Rcv Hello on ve 9 OSPFv3:
(fe80::224:38ff:fed6:7800->OSPFv3: ff02::5)
RtrID:10.2.2.2 DR:10.4.4.8 BDR:10.2.2.2
Debug: Jan 1 18:52:16 OSPFv3: Snd Hello on ve 9 OSPFv3:
(fe80::224:38ff:fe21:6400->OSPFv3: ff02::5)
RtrID:10.4.4.8 DR:10.4.4.8 BDR:10.2.2.2
Debug: Jan 1 18:52:16 OSPFv3: Rcv Hello on ve 9 OSPFv3:
(fe80::224:38ff:fed6:7800->OSPFv3: ff02::5)
RtrID:10.2.2.2 DR:10.4.4.8 BDR:10.2.2.2
Debug: Jan 1 18:52:16 OSPFv3: Rcv Hello on ve 9 OSPFv3:
(fe80::224:38ff:fed6:7800->OSPFv3: ff02::5)
RtrID:10.2.2.2 DR:10.4.4.8 BDR:10.2.2.2
debug ipv6 ospf packet-lsa-ack
Syntax: [no] debug ipv6 ospf packet-lsa-ack
This command displays all OSPFv3 LSA acknowledgment packets in rx or tx mode as shown in the
following example.
Brocade# debug ipv6 ospf packet-lsa-ack
OSPFv3: packet-lsa-ack debugging is on
Brocade(config-if-e1000-8/9)# Debug: Jan 1 20:14:33 OSPFv3: Rcv LSAck on ve 9
OSPFv3: (fe80::224:38ff:fed6:7800->OSPFv3: fe80::224:38ff:fe21:6400)
Type:2009, LSID:19320 Adv:10.4.4.8 SEQ:8000000f AGE:3600
Debug: Jan 1 20:14:33 OSPFv3: Snd LSAck on ve 9 OSPFv3:
(fe80::224:38ff:fe21:6400->OSPFv3: fe80::224:38ff:fed6:7800)
Type:2001, LSID:0 Adv:10.2.2.2 SEQ:8000003c AGE:1
Debug: Jan 1 20:14:33 OSPFv3: Snd LSAck on ve 9 OSPFv3:
(fe80::224:38ff:fe21:6400->OSPFv3: fe80::224:38ff:fed6:7800)
Type:2009, LSID:0 Adv:10.2.2.2 SEQ:80000001 AGE:3600
Debug: Jan 1 20:14:33 OSPFv3: Snd LSAck on ve 9 OSPFv3:
(fe80::224:38ff:fe21:6400->OSPFv3: fe80::224:38ff:fed6:7800)
Type:2009, LSID:0 Adv:10.2.2.2 SEQ:80000001 AGE:3600