Brocade FastIron SX, FCX, and ICX Diagnostic Reference - Manual (Page 180)

168 Brocade FastIron SX, FCX, and ICX Diagnostic Reference
53-1003076-02
MLD snooping debug commands
6
Brocade# debug pimsm-snoop show
pimsm-snoop debug-enable-any = 1
debug pimsm-snoop is enabled
debug pimsm-snoop physical_port e4/48 is enabled
debug pimsm-snoop error is enabled
debug pimsm-snoop control-source 10.85.1.3 is enabled
debug pimsm-snoop source
Syntax: [no] debug pimsm-snoop source source_address
This command displays the PIM-SM snooping related debug information for the specified source
address. Command output resembles the following example.
Brocade# debug pimsm-snoop source 10.27.27.5
Brocade# pim_snoop join (10.27.27.5 228.228.0.1), from e1/1/12
pim_snoop join (10.27.27.5 228.228.0.2), from e1/1/12
pim_snoop join (10.27.27.5 228.228.0.3), from e1/1/12
PIM from 10.27.27.2, vlan 275, port 1/1/12: Src=10.27.27.5 with 0 JOIN with 0
PRUNE
pim_snoop prune 1/1/12 from (10.27.27.5, 228.228.0.1), pim_snoop prune
1/1/12 from (10.27.27.5, 228.228.0.2), pim_snoop prune 1/1/12 from
(10.27.27.5, 228.228.0.3), PIM from 10.27.27.2, vlan 275, port 1/1/12:
Src=10.27.27.5 with 0 JOIN with 3 PRUNE, 1st Grp=228.228.0.1
pim_snoop join (10.27.27.5 228.228.0.1), from e1/1/12
pim_snoop join (10.27.27.5 228.228.0.2), from e1/1/12
pim_snoop join (10.27.27.5 228.228.0.3), from e1/1/12
PIM from 10.27.27.2, vlan 275, port 1/1/12: Src=10.27.27.5 with 0 JOIN with 0
PRUNE
MLD snooping debug commands
Multicast Listener Discovery (MLD) discovers multicast listeners, or nodes that want to receive
multicast packets on directly attached links. MLDv2 supports source filtering, the ability of a node
to send reports on traffic that is from a specific address source or from all multicast addresses
except the specified address sources. The information is then provided to the source-specific
multicast (SSM) routing protocols such as PIM-SSM.
The following commands display information related to the MLD snoop debugging.
debug mld-snoop add-del-oif all
Syntax: [no] debug mld-snoop add-del-oif all
This command displays information about the addition or deletion of all the OIFs that are MLD
snooping-enabled.
Brocade# debug mld-snoop add-del-oif all
mldsnoop add-del-oif all enabled
Brocade# Del e1/1/23 from (0x0 0x230005) vlan 130
Del e1/1/23 from (0x0 0x230004) vlan 130
Del e1/1/23 from (0x0 0x230003) vlan 130
Del e1/1/23 from (0x0 0x230002) vlan 130
Del e1/1/23 from (0x0 0x230001) vlan 130
Add e1/1/23 to (0x0 0x230001) vlan 130
Add e1/1/23 to (0x0 0x230002) vlan 130
Add e1/1/23 to (0x0 0x230003) vlan 130