Brocade FastIron SX, FCX, and ICX Diagnostic Reference User Manual
Page 172
160
Brocade FastIron SX, FCX, and ICX Diagnostic Reference
53-1003076-02
PIM debug commands
6
This command sets the PIM level. The decimal variable refers to the number of the PIM level. The
valid values are from 1 through 3.
Brocade# debug ip pim level
DECIMAL 1-3 (most detailed)
Brocade# debug ip pim level 1
debug level = 1
Brocade# rcvd PIM_V2 Hello, from 10.10.10.129 to 224.0.0.13 Len 34 on v10
0 (8/1/22)
rcvd PIM_V2 Hello, from 10.10.10.129 to 224.0.0.13 Len 34 on v100 (8/1/22)
Brocade# debug ip pim level 2
debug level = 2
Brocade# 00:21:13 Send PIM_V2 Hello Src 10.10.10.119 Dst 224.0.0.13 Len 3
4 on v100
00:21:13 Send PIM_V2 Hello Src 10.1.20.22 Dst 224.0.0.13 Len 34 on v200
00:21:13 Send PIM_V2 Hello Src 10.1.30.22 Dst 224.0.0.13 Len 34 on v300
rcvd PIM_V2 Bootstrap, from 10.10.10.129 to 224.0.0.13 Len 36 on v100 (8/1/22)
00:21:16 Send PIM_V2 Hello Src 10.10.10.119 Dst 224.0.0.13 Len 34 on v100
00:21:16 Send PIM_V2 Hello Src 10.1.20.22 Dst 224.0.0.13 Len 34 on v200
00:21:16 Send PIM_V2 Hello Src 10.1.30.22 Dst 224.0.0.13 Len 34 on v300
PIMSM: BEGIN Periodic join-prune msgs
Begin sending Join/Prune msg to v100, rpf_nbr=10.10.10.129,
group address: 225.1.1.10
send_J/P_msg(), lcl_adr=10.10.10.119 dest=224.0.0.13 pkt_size=42 to v100
group address: 225.1.1.9
send_J/P_msg(), lcl_adr=10.10.10.119 dest=224.0.0.13 pkt_size=70 to v100
group address: 225.1.1.8
send_J/P_msg(), lcl_adr=10.10.10.119 dest=224.0.0.13 pkt_size=98 to v100
group address: 225.1.1.7
send_J/P_msg(), lcl_adr=00.10.10.119 dest=224.0.0.13 pkt_size=126 to v100
group address: 225.1.1.6
send_J/P_msg(), lcl_adr=10.10.10.119 dest=224.0.0.13 pkt_size=154 to v100
group address: 225.1.1.5
send_J/P_msg(), lcl_adr=10.10.10.119 dest=224.0.0.13 pkt_size=182 to v100
group address: 225.1.1.4
send_J/P_msg(), lcl_adr=10.10.10.119 dest=224.0.0.13 pkt_size=210 to v100
group address: 226.1.1.1
send_J/P_msg(), lcl_adr=10.10.10.119 dest=224.0.0.13 pkt_size=238 to v100
group address: 225.1.1.3
send_J/P_msg(), lcl_adr=10.10.10.119 dest=224.0.0.13 pkt_size=266 to v100
group address: 225.1.1.2
send_J/P_msg(), lcl_adr=10.10.10.119 dest=224.0.0.13 pkt_size=294 to v100
group address: 225.1.1.1
send_J/P_msg(), lcl_adr=10.10.10.119 dest=224.0.0.13 pkt_size=322 to v100
group address: 226.1.1.2
send_J/P_msg(), lcl_adr=10.10.10.119 dest=224.0.0.13 pkt_size=350 to v100
group address: 227.1.1.2
send_J/P_msg(), lcl_adr=10.10.10.119 dest=224.0.0.13 pkt_size=378 to v100
group address: 227.1.1.1
send_J/P_msg(), lcl_adr=10.10.10.119 dest=224.0.0.13 pkt_size=406 to v100
00:21:16 Send PIM_V2 Join/Prune Src 10.10.10.119 Dst 224.0.0.13 Len 406 on v100
PIMSM: END Periodic join-prune msgs
Brocade# debug ip pim level 3
debug level = 3
Brocade# rcvd PIM_V2 Hello, from 10.10.10.129 to 224.0.0.13 Len 34 on v10
0 (8/1/22)
Hello msg v100, source 10.10.10.129 group 224.0.0.13
rcvd PIM_V2 Hello, from 10.10.10.129 to 224.0.0.13 Len 34 on v100 (8/1/22)
Hello msg v100, source 10.10.10.129 group 224.0.0.13