Brocade FastIron SX, FCX, and ICX Diagnostic Reference User Manual
Page 176
164
Brocade FastIron SX, FCX, and ICX Diagnostic Reference
53-1003076-02
PIM debug commands
6
PIMSM-REG.VRF0: (10.0.0.168 228.0.0.9) Sending L2-Null Reg on iface v78
PIMSM-REG.VRF0: (10.0.0.168 228.0.0.10) Sending L2-Null Reg on iface v78
PIMSM-REG.VRF0: (10.0.0.168 228.0.0.11) Sending L2-Null Reg on iface v78
PIMSM-REG.VRF0: (10.0.0.168 228.0.0.12) Sending L2-Null Reg on iface v78
PIMSM-REG.VRF0: (10.0.0.168 228.0.0.13) Sending L2-Null Reg on iface v78
PIMSM-REG.VRF0: (10.0.0.168 228.0.0.14) Sending L2-Null Reg on iface v78
PIMSM-REG.VRF0: (10.0.0.168 228.0.0.15) Sending L2-Null Reg on iface v78
PIMSM-REG.VRF0: (10.0.0.168 228.0.0.16) Sending L2-Null Reg on iface v78
PIMSM-REG.VRF0: (10.0.0.168 228.0.0.17) Sending L2-Null Reg on iface v78
PIMSM-REG.VRF0: (10.0.0.168 228.0.0.18) Sending L2-Null Reg on iface v78
PIMSM-REG.VRF0: (10.0.0.168 228.0.0.19) Sending L2-Null Reg on iface v78
PIMSM-REG.VRF0: (10.0.0.168 228.0.0.20) Sending L2-Null Reg on iface v78
PIMSM-REG.VRF0: (10.0.0.168 228.0.0.21) Sending L2-Null Reg on iface v78
PIMSM-REG.VRF0: (10.0.0.168 228.0.0.22) Sending L2-Null Reg on iface v78
debug ip pim rp
Syntax: [no] debug ip pim rp
This command controls the Rendezvouz Point (RP) processing and the command output resembles
the following example.
Brocade# debug ip pim rp
PIM: rp debugging is on
Brocade(config-if-e1000-1/1/11)# enable
Brocade(config-if-e1000-1/1/11)# PIMv4-CRP.VRF0: Sending Candidate RP Msg (size
22)
VRF0 Flow Entry Delete (10.0.0.168 232.0.0.11) HW bits: 0 0
VRF0 Flow Entry Delete (10.0.0.168 232.0.0.12) HW bits: 0 0
VRF0 Flow Entry Delete (10.0.0.168 232.0.0.13) HW bits: 0 0
VRF0 Flow Entry Delete (10.0.0.168 232.0.0.14) HW bits: 0 0
VRF0 Flow Entry Delete (10.0.0.168 232.0.0.15) HW bits: 0 0
VRF0 Flow Entry Delete (10.0.0.168 232.0.0.16) HW bits: 0 0
VRF0 Flow Entry Delete (10.0.0.168 232.0.0.17) HW bits: 0 0
VRF0 Flow Entry Delete (10.0.0.168 232.0.0.18) HW bits: 0 0
VRF0 Flow Entry Delete (10.0.0.168 232.0.0.19) HW bits: 0 0
VRF0 Flow Entry Delete (10.0.0.168 232.0.0.20) HW bits: 0 0
VRF0 Flow Entry Delete (10.0.0.168 232.0.0.21) HW bits: 0 0
debug ip pim source
Syntax: [no] debug ip pim source ipaddr
This command monitors the content related to a specific PIM server. The ipaddr variable refers to
the IP address of the PIM server source.
Brocade# debug ip pim source 10.11.10.101
Brocade# join_prune_timer, (10.11.10.101 225.1.1.10) ->num=1, rpt=0,
am_rp_and_proxy=0, JOIN
join_prune_timer, (10.11.10.101 225.1.1.10) ->num=1, rpt=0, spt=1, SRC=v100,
RP=v100
join_prune_timer, (10.11.10.101 225.1.1.10) fail RPT PRUNE cond.
join_prune_timer, (10.11.10.101 225.1.1.9) ->num=1, rpt=0, am_rp_and_proxy=0,
JOIN
join_prune_timer, (10.11.10.101 225.1.1.9) ->num=1, rpt=0, spt=1, SRC=v100,
RP=v100
join_prune_timer, (10.11.10.101 225.1.1.9) fail RPT PRUNE cond.
join_prune_timer, (10.11.10.101 225.1.1.8) ->num=1, rpt=0, am_rp_and_proxy=0,
JOIN