FlexLink XT (макс. 30 кг) Тех. обслуживание User Manual

FlexLink Equipment

Table of contents

Document Outline

Contents
- Preventive maintenance
- Mounting instructions
- Trouble shooting
- Preventive maintenance
Introduction
- General introduction
- Non FlexLink equipment
- Safety considerations
- Maintenance intervals
  - Table 1: Ready reckoner
- Spare/replacement parts
- Warranty/guarantee
XT Pallets XTPP
- Recommended inspection interval
- Check wear or damage of pallets
XT Compact conveyor XTUC S11
- Recommended inspection interval
- Check wear or damage of conveyor chain
  - 1 Run the conveyor to inspect the whole chain. Example of damage to look for is listed below:
  - 2 If any links or chain has to be replaced, see “Replace chain on XT Compact conveyor module” on ...
- Check elongation of conveyor chain (only valid for conveyor > 1500 mm)
- Check the slide rails
- Check motor temperature
XT Conveyor XTUC
- Recommended inspection interval
- Check wear or damage of conveyor chain
  - 1 Run the conveyor to inspect the whole chain. Examples of damage to look for is listed below:
  - 2 If any links or chain has to be replaced, see “Replace chain on XT conveyor module – End drive ...
- Check tension of conveyor chain
  - 1 Run the conveyor with maximum realistic amount of loaded pallets.
  - 2 Check the slack in the drive unit. If the chain is hanging below the slot (C) or past the midpo...
- Check the slide rails
Transfer units XTPT
- Recommended inspection interval
- Check wear or damage of conveyor chain
  - 1 Run the transfer to inspect the whole chain. Example of damage to look for is listed below:
  - 2 If any links or chain has to be replaced, see section “Replace chain on XT Compact conveyor mod...
- Check speed of lift and lowering movement
  - 1 Run the transfer with loaded pallets
  - 2 If necessary, adjust the throttle valves (D) at the bottom of the unit.
- Other observations
- Cleaning conveyor chain
- Other instructions
- Spare parts
Locating station XTPX P11 A
- Recommended inspection interval
- Check wear of guide pins
  - 1 Examine the guide pins (A).
  - 2 If the guide pins have to be replaced see “Mounting guide pins to locating, lift-and-rotate and...
- Check docking of pallet
  - 1 Run the unit and check that the pins enter the pallet bushings in a smooth way without jam and ...
  - 2 If the locating units have to be adjusted due to jam, see separate publication "Assembly manual...
- Check speed of lift and lowering movement
- Other observations
- Spare parts
Lift and locate stations XTPX P12
- Recommended inspection interval
- Check wear of guide pins
  - 1 Examine the guide pins (A).
  - 2 If the guide pins have to be replaced see “Mounting guide pins to locating, lift-and-rotate and...
- Check docking of pallet
  - 1 Run the unit and check that the pins enter the pallet bushings in a smooth way without jam and ...
- Check speed of lift and lowering movement
  - 1 Run the unit with loaded pallets.
  - 2 If necessary, adjust the throttle valves (B) on the cylinder units.
- Other observations
- Spare parts
Lift and rotate station XTPR
- Recommended inspection interval
- Check wear of guide pins
  - 1 Examine the guide pins (A).
  - 2 If the guide pins have to be replaced see “Mounting guide pins to locating, lift-and-rotate and...
- Check docking of pallet
  - 1 Run the unit and check that the pins enter the pallet bushings in a smooth way without jam and ...
  - 2 If the locating units have to be adjusted due to jam, try to adjust the end positions of the ro...
- Check speed of lift and lowering movement
  - 1 Run the unit with loaded pallets.
  - 2 If necessary, adjust the throttle valves (C) at the cylinder units.
- Check speed of rotating movement
  - 1 Run the unit with loaded pallets.
  - 2 If necessary, adjust the throttle valves (D) on the cylinder units.
- Other observations
- Spare parts
Stops and dampers
- Recommended inspection interval
- Check the damping function
  - 1 Check the damping function.
  - 2 If needed, fine adjust the damping function (A) when the system is running.
- Check noise level
  - 1 Check the noise level.
  - 2 If needed, adjust the external non-return throttle valve (B) to reduce noise level. (Throttle v...
- Other observations
- Spare parts
- Mounting instructions
Replace chain on XT conveyor module – End drive unit
- Introduction
- Tools
- Instruction
Replace chain on XT conveyor module – Catenary drive unit
- Introduction
- Tools
- Instruction
Replacement of slide rail
- Introduction
- Tools
- Instruction
Replace motor on XT conveyor drive unit – Side mounted
- Introduction
- Tools
- Instruction
Replace motor on XT conveyor drive unit – Centre mounted
- Introduction
- Tools
- Instruction
Replace chain on XT Compact conveyor module
- Introduction
- Tools
- Instruction
Replace driving belt on XT Compact conveyor module
- Introduction
- Tools
- Instruction
Replace motor on XT Compact conveyor module
- Introduction
- Tools
- Instruction
Replace motor on XT transfer unit XTPT M1
- Introduction
- Tools
- Instruction
  - 1 Remove the screws (8°) on the transfer unit covers on both sides. Use the Phillips screwdriver....
  - 2 Remove the screws (2x) holding the motor, use the 5 mm Allen key and the 10 mm box wrench.
Replace motor on XT transfer unit XTPT M2
- Introduction
- Tools
- Instruction
Replace driving belt on XT transfer unit XTPT M1
- Introduction
- Tools
- Instruction
Replace driving belt on XT transfer unit XTPT M2
- Introduction
- Tools
- Instruction
Mounting guide pins to locating, lift-and-rotate and lift-and-locate station
- Introduction
- Tools
- Instruction
- Trouble shooting
XT Compact conveyor XTUC S11
- XT Conveyor XTUC _51/52
- XT Transfer unit XTPT PWxPL
- XT Locating station XTPX P11 A
- XT Lift & Locate station XTPX P12
- XT Lift & Rotate station XTPR
- Stops and dampers