KEPCO KLP Series User Manual, Rev 4 - Manual (Page 8)

ii
KLP SVC 091313
TABLE OF CONTENTS
SECTION PAGE
3.2.2 Setting Local/Remote Mode ................................................................................................................... 3-3
3.2.2.1 Remote with Local (Front Panel) Lockout ......................................................................................... 3-4
3.2.3 Menu Structure ....................................................................................................................................... 3-4
3.2.4 Setting VOLTAGE and CURRENT Control Coarse/Fine Preference ..................................................... 3-4
3.2.5 Enabling/Disabling Output Power ........................................................................................................... 3-5
3.2.6 Enabling/Disabling the Output using Remote Inhibit .............................................................................. 3-6
3.2.7 Checking Voltage/Current Setpoints....................................................................................................... 3-7
3.2.8 Password Protected Functions ............................................................................................................... 3-7
3.2.9 Defining a Virtual Model.......................................................................................................................... 3-7
3.2.10 Setting voltage or current........................................................................................................................ 3-8
3.2.10.1 Real-time Voltage/Current Adjustment .............................................................................................. 3-9
3.2.10.2 Setpoint Adjustment .......................................................................................................................... 3-9
3.2.10.3 Last Setting Recall............................................................................................................................. 3-9
3.2.11 Viewing/Changing Overvoltage or Overcurrent Protection Values ......................................................... 3-10
3.2.12 Changing GPIB Address......................................................................................................................... 3-10
3.2.13 Changing RS 232 Baud Rate [Standard Models Only]........................................................................... 3-11
3.2.14 Setting up Master/Slave Configurations [Standard Models Only]........................................................... 3-11
3.2.14.1 Configure power supply as Slave [Standard Models Only] ............................................................... 3-11
3.2.14.2 Configure power supply as Master [Standard Models Only] ............................................................. 3-12
3.2.14.3 Operating the Master/Slave Configuration [Standard Models Only].................................................. 3-13
3.2.14.4 Restoring the Master/Slave Configuration to Standalone operation [Standard Models Only] ........... 3-14
3.2.15 LAN Interface Configuration [E-series Models Only] .............................................................................. 3-14
3.2.16 Unit Configuration ................................................................................................................................... 3-16
3.2.17 Utility Function ........................................................................................................................................ 3-16
3.2.17.1 Internal Relay Control........................................................................................................................ 3-17
3.2.17.2 Quick Boot ......................................................................................................................................... 3-18
3.2.17.3 System Configuration Functions........................................................................................................ 3-19
3.2.17.3.1 Remote Inhibit Polarity ................................................................................................................ 3-19
3.2.17.3.2 Fault Recovery Mode .................................................................................................................. 3-19
3.2.17.4 Analog Output Full Scale Calibration................................................................................................. 3-21
3.2.17.5 Analog Input Full Scale Calibration ................................................................................................... 3-22
3.2.17.6 Calibration ......................................................................................................................................... 3-22
3.3 Remote Mode Programming Using Digital Interfaces ................................................................................ 3-22
3.3.1 Factory Default Settings ......................................................................................................................... 3-22
3.3.1.1 GPIB Factory Defaults....................................................................................................................... 3-22
3.3.1.2 RS 232 Factory Defaults [Standard Models Only]............................................................................. 3-23
3.3.1.3 LAN Factory Defaults [E-Series Models Only]................................................................................... 3-23
3.3.2 Additional Functions Not Available from the Front Panel ....................................................................... 3-24
3.3.3 Remote Programming Using the IVI-COM Instrument Driver................................................................. 3-24
3.3.4 Remote Programming Using the LabView G Instrument Driver ............................................................. 3-24
3.3.5 Remote Programming Using the VXI plug&play Instrument Driver ........................................................ 3-24
3.3.6 Remote Programming Using the Web Interface [E-series Models Only]................................................ 3-24
3.3.6.1 Troubleshooting LAN Communication Problems............................................................................... 3-25
3.3.6.2 Finding Kepco Power Supplies on the LAN [E-Series Models Only]................................................. 3-25
3.3.6.3 Launch Web Interface [E-Series Models Only].................................................................................. 3-26
3.3.6.4 Instrument Configuration Using Web Interface [E-Series Models Only]............................................ 3-27
3.3.6.5 LAN Configuration Using Web Interface [E-Series Models Only]...................................................... 3-28
3.3.6.6 Operating The Unit Using Web Interface [E-Series Models Only]..................................................... 3-30
3.3.6.6.1 Changing the Output [E-Series Models Only] ............................................................................. 3-30
3.3.6.6.2 Changing Protection [E-Series Models Only] .............................................................................. 3-30
3.3.6.6.3 Using Save and Recall [E-Series Models Only] .......................................................................... 3-30
3.3.6.6.4 Resetting the Unit (*RST) [E-Series Models Only] ...................................................................... 3-32