KEPCO KLP Series User Manual, Rev 4 Instruction Manuals and User Guides
We have 7 Instruction Manuals and User Guides for KLP Series User Manual, Rev 4 KEPCO
Manuals 
| Recognized languages: | English |
|---|---|
| Pages: | 94 |
| Size: | 2.13 MB |
Show table of contents
Document Outline
- SECTION 1 - INTRODUCTION
- SECTION 2 - INSTALLATION
- SECTION 3 - OPERATION
- SECTION 4 - CALIBRATION
- FIGURE 1-1. KLP Series Power Supply
- SECTION 1 - INTRODUCTION
- 1.1 Scope of Manual
- 1.2 General Description
- 1.3 Options
- 1.3.1 Rapid Output Discharge Circuit (RODC) Option (R Suffix)
- TABLE 1-1. Rapid Output Discharge Circuit Improvement in Output Response Time
- 1.4 Specifications
- FIGURE 1-2. KLP Operating Regions
- TABLE 1-2. Model Parameters
- TABLE 1-3. KLP Specifications
- FIGURE 1-3. KLP Series Power Supply, Mechanical Outline Drawing
- 1.5 Features
- 1.5.1 Local Control
- 1.5.2 Remote Control
- 1.5.2.1 Digital Programming
- 1.5.2.2 Analog Programming
- 1.5.3 Digital Calibration
- 1.5.4 Overvoltage/Overcurrent Protection
- 1.5.5 User-defined Voltage/Current Limits (Virtual Models)
- 1.5.6 Storage of User-Programmed Active Settings
- 1.5.7 User-Programmed Sequences
- 1.5.8 Last Setting Recall
- 1.5.9 Built-in Protection
- 1.5.10 Internal Relay
- 1.5.11 Master/Slave Control [standard models Only]
- 1.6 Equipment Supplied
- TABLE 1-4. Equipment Supplied
- 1.7 Accessories
- 1.8 Safety
- TABLE 1-5. Accessories
- TABLE 1-6. Safety Symbols
- SECTION 2 - INSTALLATION
- 2.1 Unpacking and Inspection
- 2.2 Terminations and Controls
- 2.2.1 Front Panel Controls and Indicators.
- FIGURE 2-1. KLP Series, Front Panel Controls and Indicators
- TABLE 2-1. Controls, and Indicators
- 2.2.2 Rear Panel Connectors and Switches.
- TABLE 2-2. Analog I/O Switch Functions
- FIGURE 2-2. KLP Series, Rear Panel Switch and Connectors
- TABLE 2-3. IEEE 488 Port Connector (J4) Pin Assignments
- TABLE 2-4. RS 232 Port Connector (J3) Pin Assignments [Standard Models Only]
- TABLE 2-5. LAN Port Connector (J7) Pin Assignments [E-Series Models Only]
- TABLE 2-6. Control Input Terminal block Assignments
- TABLE 2-7. Analog I/O Connector (J2) Pin Assignments
- 2.3 Source Power Requirements
- 2.4 Cooling
- 2.5 Preliminary Operational Check
- 2.6 Installation
- 2.6.1 Rack Mounting
- 2.7 Wiring Instructions
- 2.7.1 Safety Grounding
- 2.7.2 Source Power
- 2.7.2.1 Current Rating
- TABLE 2-8. Input Current Service Rating and Conductor Sizes
- 2.7.2.2 Connections
- 2.7.3 D-C Output Grounding
- 2.7.4 Power Supply/Load Interface
- 2.7.5 Load Connection - General
- 2.7.5.1 Local Sensing/Remote Sensing Select
- FIGURE 2-3. Remote Sensing
- 2.7.6 Series Operation
- 2.7.7 Parallel Operation
- FIGURE 2-4. Series Connection using Remote Sensing
- FIGURE 2-5. Parallel Connections Using Remote Sensing
- 2.7.7.1 Load Sharing
- 2.7.8 Master/Slave Configurations [Standard Models Only]
- 2.7.9 Analog I/O Connections
- 2.8 Digital Connections
- 2.8.1 GPIB Connections
- 2.8.2 RS 232 Connections [Standard Models Only]
- 2.8.3 LAN Connections [E-Series Models Only]
- SECTION 3 - OPERATION
- 3.1 General
- 3.2 Local Mode Operation
- 3.2.1 Turning the Power Supply On
- TABLE 3-1. Power-up Built-in Test Error Codes
- 3.2.2 Setting Local/Remote Mode
- 3.2.2.1 Remote with Local (Front Panel) Lockout
- 3.2.3 Menu Structure
- 3.2.4 Setting VOLTAGE and CURRENT Control Coarse/Fine Preference
- FIGURE 3-1. Function Switch Menu Structure
- 3.2.5 Enabling/Disabling Output Power
- 3.2.6 Enabling/Disabling the Output using Remote Inhibit
- 3.2.7 Checking Voltage/Current Setpoints
- 3.2.8 Password Protected Functions
- 3.2.9 Defining a Virtual Model
- 3.2.10 Setting voltage or current
- 3.2.10.1 Real-time Voltage/Current Adjustment
- 3.2.10.2 Setpoint Adjustment
- 3.2.10.3 Last Setting Recall
- 3.2.11 Viewing/Changing Overvoltage or Overcurrent Protection Values
- 3.2.12 Changing GPIB Address
- 3.2.13 Changing RS 232 Baud Rate [Standard Models Only]
- 3.2.14 Setting up Master/Slave Configurations [Standard Models Only]
- 3.2.14.1 Configure power supply as Slave [Standard Models Only]
- 3.2.14.2 Configure power supply as Master [Standard Models Only]
- 3.2.14.3 Operating the Master/Slave Configuration [Standard Models Only]
- 3.2.14.4 Restoring the Master/Slave Configuration to Standalone operation [Standard Models Only]
- 3.2.15 LAN Interface Configuration [E-series Models Only]
- 3.2.16 Unit Configuration
- 3.2.17 Utility Function
- 3.2.17.1 Internal Relay Control
- 3.2.17.2 Quick Boot
- 3.2.17.3 System Configuration Functions
- 3.2.17.3.1 Remote Inhibit Polarity
- 3.2.17.3.2 Fault Recovery Mode
- TABLE 3-2. Fault Recovery Configuration
- FIGURE 3-2. Fault Recovery Configuration Display
- 3.2.17.4 Analog Output Full Scale Calibration
- 3.2.17.5 Analog Input Full Scale Calibration
- 3.2.17.6 Calibration
- 3.3 Remote Mode Programming Using Digital Interfaces
- 3.3.1 Factory Default Settings
- 3.3.1.1 GPIB Factory Defaults
- 3.3.1.2 RS 232 Factory Defaults [Standard Models Only]
- 3.3.1.3 LAN Factory Defaults [E-Series Models Only]
- 3.3.2 Additional Functions Not Available from the Front Panel
- 3.3.3 Remote Programming Using the IVI-COM Instrument Driver
- 3.3.4 Remote Programming Using the LabView G Instrument Driver
- 3.3.5 Remote Programming Using the VXI plug&play Instrument Driver
- 3.3.6 Remote Programming Using the Web Interface [E-series Models Only]
- 3.3.6.1 Troubleshooting LAN Communication Problems.
- 3.3.6.2 Finding Kepco Power Supplies on the LAN [E-Series Models Only]
- FIGURE 3-3. PS Find Screen
- 3.3.6.3 Launch Web Interface [E-Series Models Only]
- FIGURE 3-4. Web Interface Home Page (Unit Description)
- 3.3.6.4 Instrument Configuration Using Web Interface [E-Series Models Only]
- FIGURE 3-5. Web Interface Configure Instrument Page
- 3.3.6.5 LAN Configuration Using Web Interface [E-Series Models Only]
- FIGURE 3-6. Web Interface Configure LAN Page
- 3.3.6.6 Operating The Unit Using Web Interface [E-Series Models Only]
- 3.3.6.6.1 Changing the Output [E-Series Models Only]
- 3.3.6.6.2 Changing Protection [E-Series Models Only]
- 3.3.6.6.3 Using Save and Recall [E-Series Models Only]
- FIGURE 3-7. Web Interface Operate Instrument Page
- FIGURE 3-8. Protection Dialog Box
- FIGURE 3-9. Save/Recall Dialog Box
- 3.3.6.6.4 Resetting the Unit (*RST) [E-Series Models Only]
- FIGURE 3-10. Reset Dialog Box
- 3.3.6.6.5 Using a List (User-Programmed Sequences) [E-Series Models Only]
- FIGURE 3-11. List Dialog Box
- FIGURE 3-12. Adding Multiple Steps (Ramps) to List
- 3.3.6.6.6 Setting Virtual Model [E-Series Models Only]
- FIGURE 3-13. Virtual Model Dialog Box
- 3.4 Remote Programming Using Analog Signals
- 3.4.1 Programming with external resistance
- FIGURE 3-14. Analog Programming of Output Voltage or Current using Resistance
- 3.4.2 Programming with external Voltage
- FIGURE 3-15. Analog Programming of Output Voltage or Current using Voltage
- 3.4.3 Changing Overvoltage or Overcurrent Protection Values in Analog Programming Mode
- SECTION 4 - CALIBRATION
- 4.1 General
- 4.2 Equipment Required
- 4.3 Calibration Using Front Panel Controls in Local Mode
- FIGURE 4-1. Analog Port Wiring for Calibration
- 4.3.1 Voltage Calibration (Local)
- 4.3.2 Current Calibration (Local)
- 4.3.3 External Calibration (Local)
- 4.3.4 Calibration Exit (Local)
- 4.4 Calibration using VXI plug&play Driver
- FIGURE 4-2. Calibration Window
- 4.4.1 Voltage Calibration (VXI plug&play Driver Demo)
- FIGURE 4-3. Voltage Calibration Window
- 4.4.2 Current Calibration (VXI plug&play Demo)
- FIGURE 4-4. Current Calibration Window
- 4.4.3 Analog Reference Calibration (VXI plug&play Demo)
- FIGURE 4-5. Analog Reference Calibration Window
- 4.4.4 Calibration Exit (VXI plug&play Demo)
- 4.5 Changing the Calibration Password
- Table 4-1. Factory Default Unit Passwords
- 4.6 Restoring Prior Calibration Values
- KLP Installation/Operation Summary
| Recognized languages: | English |
|---|---|
| Pages: | 110 |
| Size: | 2.09 MB |
Show table of contents
Document Outline
- SECTION 1 - INTRODUCTION
- SECTION 2 - INSTALLATION
- SECTION 3 - OPERATION
- SECTION 4 - CALIBRATION
- FIGURE 1-1. KLP Series Power Supply
- SECTION 1 - INTRODUCTION
- 1.1 Scope of Manual
- 1.2 General Description
- 1.3 Specifications
- FIGURE 1-2. KLP Operating Regions
- TABLE 1-1. Model Parameters
- TABLE 1-2. KLP Specifications
- FIGURE 1-3. KLP Series Power Supply, Mechanical Outline Drawing
- 1.4 Features
- 1.4.1 Local Control
- 1.4.2 Remote Control
- 1.4.2.1 Digital Programming
- 1.4.2.2 Analog Programming
- 1.4.3 Digital Calibration
- 1.4.4 Overvoltage/Overcurrent Protection
- 1.4.5 Userdefined Voltage/Current Limits (Virtual Models)
- 1.4.6 Storage of User-Programmed Active Settings
- 1.4.7 User-Programmed Sequences
- 1.4.8 Last Setting Recall
- 1.4.9 Built-in Protection
- 1.4.10 Internal Relay
- 1.4.11 Master/Slave Control
- 1.5 Equipment Supplied
- TABLE 1-3. Equipment Supplied
- 1.6 Accessories
- 1.7 Safety
- TABLE 1-4. Accessories
- TABLE 1-5. Safety Symbols
- SECTION 2 - INSTALLATION
- 2.1 Unpacking and Inspection
- 2.2 Terminations and Controls
- 2.2.1 Front Panel Controls and Indicators.
- 2.2.2 Rear Panel Connectors and Switch.
- FIGURE 2-1. KLP Series, Front Panel Controls and Indicators
- TABLE 2-1. Controls, and Indicators
- FIGURE 2-2. KLP Series, Rear Panel Switch and Connectors
- TABLE 2-2. Analog I/O Switch Functions
- TABLE 2-3. IEEE 488 Port Connector (J4) Pin Assignments
- TABLE 2-4. RS232 Port Connector (J3) Pin Assignments
- TABLE 2-5. Rear Terminal block Assignments
- TABLE 2-6. Analog I/O Connector (J2) Pin Assignments
- 2.3 Source Power Requirements
- 2.4 Cooling
- 2.5 Preliminary Operational Check
- 2.6 Installation
- 2.6.1 Rack Mounting
- 2.7 Wiring Instructions
- 2.7.1 Safety Grounding
- 2.7.2 Source Power
- 2.7.2.1 Current Rating
- TABLE 2-7. Input Current Service Rating and Conductor Sizes
- 2.7.2.2 Connections
- 2.7.3 DC Output Grounding
- 2.7.4 Power Supply/Load Interface
- 2.7.5 Load Connection General
- 2.7.5.1 Local Sensing/Remote Sensing Select
- FIGURE 2-3. Remote Sensing
- 2.7.6 Series Operation
- 2.7.7 Parallel/redundant Operation
- FIGURE 2-4. Series Connection using Remote Sensing
- FIGURE 2-5. Parallel Connections Using Remote Sensing
- 2.7.7.1 Load Sharing
- 2.7.8 Master/Slave Configurations
- 2.7.9 Analog I/O Connections
- 2.7.10 Internal Relay Configuration
- SECTION 3 - OPERATION
- 3.1 General
- 3.2 Local Mode Operation
- 3.2.1 Turning the Power Supply On
- TABLE 3-1. Power-up Built-in Test Error Codes
- 3.2.2 Setting Local/Remote Mode
- 3.2.2.1 Remote with Local (Front Panel) Lockout
- 3.2.3 Enabling/Disabling Output Power
- 3.2.4 Checking Voltage/Current Setpoints
- 3.2.5 Defining a Virtual Model
- 3.2.6 Setting voltage or current
- 3.2.6.1 Real-time Voltage/Current Adjustment
- 3.2.6.2 Setpoint Adjustment
- 3.2.6.3 Last Setting Recall
- 3.2.7 Viewing/Changing Overvoltage or Overcurrent Protection Values
- 3.2.8 Changing GPIB Address
- 3.2.9 Changing RS232 Baud Rate
- 3.2.10 Setting up Master/Slave Configurations
- 3.2.10.1 Configure power supply as Master
- 3.2.10.2 Configure power supply as Slave
- 3.2.10.3 Operating the Master/Slave Configuration
- 3.2.11 Utility Function
- 3.2.11.1 Display System Firmware Version
- 3.2.11.2 Display Model
- 3.2.11.3 Relay Control
- 3.2.11.4 Quick Boot
- 3.2.11.5 Analog Input Full SCale Calibration
- 3.2.11.6 Calibration
- 3.3 Digital Remote Mode Programming Using SCPI commands
- 3.3.1 Additional Functions Available via Digital Remote Programming
- 3.3.1.1 Storage of User-programmed Active Settings
- 3.3.1.2 User-determined output Sequences
- 3.3.1.3 External Triggering
- 3.3.1.4 Internal Relay Configuration
- 3.4 RS232-C Operation
- 3.4.1 Serial Interface
- 3.4.2 RS 232 Implementation
- FIGURE 3-1. RS 232 Implementation
- 3.4.2.1 Echo Mode
- 3.4.2.2 Prompt Method
- 3.4.2.3 XON XOFF Method
- 3.4.2.4 Isolating RS 232 Communications Problems
- 3.5 IEEE 488 (GPIB) Bus Protocol
- 3.5.1 Changing the GPIB Address
- TABLE 3-2. IEEE 488 (GPIB) Bus Interface Functions
- TABLE 3-3. IEEE 488 (GPIB) Bus Command Mode Messages
- TABLE 3-4. IEEE 488 (GPIB) Bus Data Mode Messages
- 3.5.2 KLP VISA Instrument driver
- 3.6 SCPI Programming
- 3.6.1 SCPI Messages
- 3.6.2 Common Commands/Queries
- 3.6.3 SCPI Subsystem Command/Query Structure
- 3.6.3.1 ABORt Subsystem
- 3.6.3.2 DISPlay Subsystem
- 3.6.3.3 TRIGger Subsystem
- 3.6.3.4 LIST Subsystem
- 3.6.3.5 MEASure Subsystem
- 3.6.3.6 OUTPut Subsystem
- 3.6.3.7 STATus Subsystem
- 3.6.3.8 SYSTem subsystem
- 3.6.3.9 [SOURce:]VOLTage and [SOURce:]CURRent Subsystems
- 3.6.3.10 CALibrate Subsystem
- 3.6.4 Program Message Structure
- 3.6.4.1 Keyword
- TABLE 3-5. Rules Governing Shortform Keywords
- 3.6.4.2 Keyword Separator
- 3.6.4.3 Query Indicator
- 3.6.4.4 Data
- 3.6.4.5 Data Separator
- FIGURE 3-2. Message Structure
- 3.6.4.6 Message Unit Separator
- 3.6.4.7 Root Specifier
- 3.6.4.8 Message Terminator
- 3.6.5 Understanding The Command Structure
- FIGURE 3-3. Tree Diagram of SCPI Commands Used with KLP Power Supply
- 3.6.6 Program Message Syntax Summary
- 3.6.7 Status Reporting
- 3.6.7.1 Status Reporting Structure
- FIGURE 3-4. Status Reporting Structure
- 3.6.7.2 Operational Status Register
- 3.6.7.3 QUEStionable Status Register
- 3.6.8 SCPI Program Examples
- 3.7 Remote Programming Using Analog Signals
- 3.7.1 Enabling/Disabling the Output using Analog Control
- FIGURE 3-5. Typical Example Of KLP Power Supply Program Using SCPI Commands
- 3.7.2 Programming with external resistance
- FIGURE 3-6. Analog Programming of Output Voltage or Current using Resistance
- 3.7.3 Programming with external Voltage
- FIGURE 3-7. Analog Programming of Output Voltage or Current using Voltage
- 3.7.4 Changing Overvoltage or Overcurrent Protection Values in Analog Programming Mode
- SECTION 4 - CALIBRATION
- 4.1 General
- 4.2 Equipment Required
- 4.3 Calibration Using Front Panel Controls in Local Mode
- 4.3.1 Voltage Calibration (Local)
- 4.3.2 Current Calibration (Local)
- 4.3.3 External Calibration (Local)
- 4.3.4 Calibration Exit (Local)
- 4.4 Calibration using VISA Driver Demo Program Soft Panel
- 4.4.1 Voltage Calibration (VISA Demo)
- 4.4.2 Current Calibration (VISA Demo)
- 4.4.3 Analog Reference Calibration (VISA Demo)
- 4.4.4 Calibration Exit (VISA Demo)
- 4.5 Changing the Calibration Password
- Table 4-1. Factory Default Calibration Passwords
- 4.6 Restoring Prior Calibration Values
- APPENDIX A - IEEE 488.2 COMMAND/QUERY DEFINITIONS
- TABLE A-1. IEEE 488.2 Command/query Index
- A.2 *CLS — Clear Status Command
- A.3 *ESE — Standard Event Status Enable Command
- TABLE A-2. Standard Event Status Enable Register and Standard Event Status Register Bits
- A.4 *ESE? — Standard Event Status Enable Query
- A.5 *ESR? — Event Status Register Query
- A.6 *IDN? — Identification Query
- A.7 *OPC — Operation Complete Command
- A.8 *OPC? — Operation Complete Query
- FIGURE A-1. GPIB Commands
- A.9 *RCL — Recall Command
- A.10 *RST — Reset Command
- A.11 *SAV — Save Command
- A.12 *SRE — Service Request Enable Command
- TABLE A-3. Service Request Enable and Status Byte Register Bits
- A.13 *SRE? — Service Request Enable Query
- A.14 *STB? — Status Byte Register Query
- A.15 *TRG — Trigger Command
- A.16 *TST? — Self Test Query
- APPENDIX B - SCPI COMMAND/QUERY DEFINITIONS
- B.1 Introduction
- TABLE B-1. SCPI Subsystem Command/query Index
- B.2 Numerical Values
- B.3 ABORt Command
- B.4 CAL Commands and Queries
- B.5 DISPlay:TEXT? Query
- B.6 INITiate[:IMMediate] Command
- FIGURE B-1. Programming the Output
- B.7 INITiate:CONTinuous Command
- B.8 INITiate:CONTinuous? Query
- B.9 [SOURce:]LIST:CLEar Command
- B.10 [SOURce:]LIST:CONTrol Command
- B.11 [SOURce:]LIST:CONTrol? QUERY
- B.12 [SOURce:]LIST:COUNt Command
- B.13 [SOURce:]LIST:COUNt? Query
- B.14 [SOURce:]LIST:COUNt:SKIP Command
- B.15 [SOURce:]LIST:COUNt:SKIP? Query
- B.16 [SOURce:]LIST:CURRent Command
- B.17 [SOURce:]LIST:CURRent? Query
- B.18 [SOURce:]LIST:CURRent:POINts? Query
- B.19 [SOURce:]LIST:DIRection Command
- B.20 [SOURce:]LIST:DIRection? Query
- B.21 [SOURce:]LIST:DWELl Command
- B.22 [SOURce:]LIST:DWELl? Query
- B.23 [SOURce:]LIST:DWELl:POINts? Query
- B.24 [SOURce:]LIST:QUERy Command
- B.25 [SOURce:]LIST:QUERy? Query
- B.26 [SOURce:]LIST:VOLTage Command
- B.27 [SOURce:]LIST:VOLTage? Query
- B.28 [SOURce:]LIST:VOLTage:POINts? Query
- B.29 MEASure[:SCALar]:CURRent[:DC]? Query
- FIGURE B-2. Using LIST Commands and Queries
- B.30 MEASure:VOLTage[:SCALar][:DC]? Query
- B.31 OUTPut[:STATe] Command
- B.32 OUTPut[:STATe] Query
- B.33 OUTPut[:STATe]:PROTect:DELay Command
- B.34 OUTPut[:STATe]:PROTect:DELay? Query
- B.35 [SOURce:]CURRent[:LEVel][:IMMediate][:AMPlitude] Command
- B.36 [SOURce:]CURRent[:LEVel][:IMMediate][:AMPlitude]? Query
- B.37 [SOURce:]CURRent:LIMit:HIGH Command
- B.38 [SOURce:]CURRent:LIMit:HIGH? Query
- B.39 [SOURce:]CURRent:MODE Command
- B.40 [SOURce:]CURRent:MODE? Query
- FIGURE B-3. Programming Virtual Models
- B.41 [SOURce:]CURRent:PROTection[:LEVel] Command
- B.42 [SOURce:]CURRent:PROTection[:LEVel]? Query
- FIGURE B-4. Programming as a Current Stabilizer
- B.43 [SOURce:]CURRent:[:LEVel]TRIGgered[:AMPlitude] Command
- B.44 [SOURce:]CURRent:[:LEVel]TRIGgered[:AMPlitude]? Query
- B.45 [SOURce:]FUNCtion:MODE Command
- B.46 [SOURce:]FUNCtion:MODE? Query
- B.47 [SOURce:]VOLTage[:LEVel][:IMMediate][:AMPlitude] Command
- B.48 [SOURce:]VOLTage[:LEVel][:IMMediate][:AMPlitude]? Query
- B.49 [SOURce:]VOLTage:LIMit:HIGH Command
- B.50 [SOURce:]VOLTage:LIMit:HIGH? Query
- B.51 [SOURce:]VOLTage:MODE Command
- B.52 [SOURce:]VOLTage:MODE? Query
- B.53 [SOURce:]VOLTage:PROTection[:LEVel] Command
- B.54 [SOURce:]VOLTage:PROTection[:LEVel]? Query
- B.55 [SOURce:]VOLTage:[:LEVel]TRIGgered[:AMPlitude] Command
- FIGURE B-5. Programming as Voltage Stabilizer
- B.56 [SOURce:]VOLTage:[:LEVel]TRIGgered[:AMPlitude]? Query
- B.57 STATus:OPERation:CONDition Query
- TABLE B-2. Operation Condition Register, Operation Enable Register, and Operation Event Register ...
- B.58 STATus:OPERation:ENABle Command
- FIGURE B-6. Using Status Commands and Queries
- B.59 STATus:OPERation:ENABle? Query
- B.60 STATus:OPERation[:EVENt] Query
- B.61 STATus:PRESet Command
- B.62 STATus:QUEStionable[:EVENt]? Query
- TABLE B-3. Questionable Event Register, Questionable Condition Register and Questionable Conditio...
- B.63 STATus:QUEStionable:CONDition? Query
- B.64 STATus:QUEStionable:ENABle Command
- B.65 STATus:QUEStionable:ENABle? Query
- B.66 SYSTem:COMMunication:GPIB:ADDRess Command
- B.67 SYSTem:COMMunication:GPIB:ADDRess ? Query
- B.68 SYSTem:COMMunication:SERial:BAUD CommanD
- B.69 SYSTem:COMMunication:SERial:BAUD? Query
- B.70 SYSTem:COMMunication:SERial:ECHO Command
- B.71 SYSTem:COMMunication:SERial:ECHO? Query
- B.72 SYSTem:COMMunication:SERial:ENABle Command
- B.73 SYSTem:COMMunication:SERial:ENAB? Query
- B.74 SYSTem:COMMunication:SERial:PACE Command
- B.75 SYSTem:COMMunication:SERial:PACE? Query
- B.76 SYSTem:COMMunication:SERial:PROMpt Command
- B.77 SYSTem:COMMunication:SERial:PROMpt? Query
- B.78 SYSTem:ERRor? Query
- B.79 SYSTem:ERRor:CODE? Query
- B.80 SYSTem:ERRor:CODE:ALL? Query
- B.81 SYSTem:KLOCk Command
- B.82 SYSTem:KLOCk? Query
- FIGURE B-7. Using System Commands and Queries
- B.83 SYSTem:LANGuage Command
- B.84 SYSTem:LANGuage? Query
- B.85 SYSTem:PASSword:CENable Command
- B.86 SYSTem:PASSword:CDISable Command
- B.87 SYSTem:PASSword:NEW Command
- B.88 SYSTem:PASSword:STATe? Query
- B.89 SYSTem:SECurity:IMMediate Command
- B.90 SYSTem:SET Command
- B.91 SYSTem:SET? Query
- B.92 SYSTem:VERSion Query
- B.93 TRIGger:SOURce Command
- TABLE B-4. Error Messages
| Recognized languages: | English |
|---|---|
| Pages: | 16 |
| Size: | 295 KB |
Show table of contents
Document Outline
- BHK-MG 200 WATT (FULL RACK) AND 40 WATT (1/2 RACK) VISA INSTRUMENT DRIVER
- 1. VISA Instrument Driver Functions
- 2. Demonstration Program Using the VISA Driver
- 2.1 GPIB Setup
- 2.2 Main Panel
- FIGURE 4. Protection Window
- FIGURE 5. Store/Recall Window
- FIGURE 6. Trigger Window
- FIGURE 7. Calibration Window (Half Rack)
- FIGURE 8. Calibration Window (Full Rack)
- FIGURE 9. About Window
- FIGURE 10. Limits Window
- FIGURE 11. Program Lists Window
- FIGURE 12. Format for Typical Comma-Delineated Pattern Generation File
- FIGURE 13 Pattern Generation Window
- TABLE 3. Pattern Generation, Example 1
- TABLE 4. Pattern Generation. Example 2
- FIGURE 14. Pattern Execution Window
- FIGURE 15. Utilities Window
- FIGURE 16. Display Change Window
- FIGURE 17. Update Firmware Window
- FIGURE 18. Power Supply Event Window
- 3. Programming Examples.
- 3.1 Example 1:
- 3.2 Example 2:
| Recognized languages: | English |
|---|---|
| Pages: | 10 |
| Size: | 167 KB |
| Recognized languages: | English |
|---|---|
| Pages: | 94 |
| Size: | 1.06 MB |
Show table of contents
Document Outline
- SECTION 1 - INTRODUCTION
- SECTION 2 - INSTALLATION
- SECTION 3 - OPERATION
- FIGURE 1-1. ATE-DMG Series Programmable Power Supply
- SECTION 1- INTRODUCTION
- 1.1 Scope of Manual
- 1.2 General Description
- 1.3 Specifications
- 1.4 Local Control
- 1.5 Remote Control
- TABLE 1-1. ATE-DMG D-C Output Ratings and output impedance
- TABLE 1-2. ATE-DMG Series Specifications
- TABLE 1-3. ATE Dynamic Specifications, Resistive Load
- TABLE 1-4. Overvoltage/Overcurrent Settings
- TABLE 1-5. ATE Static Specifications
- 1.6 Features
- 1.6.1 Overvoltage/Overcurrent Protection
- 1.6.1.1 Programmable Overvoltage/Overcurrent Delay
- 1.6.1.2 Crowbar Circuit
- 1.6.2 Non-volatile Storage of Programmed Sequences or Active Settings
- 1.6.3 User-defined Voltage/Current Limits
- 1.7 Equipment Supplied
- 1.8 Accessories
- TABLE 1-6. Accessories
- 1.9 Safety
- TABLE 1-7. Safety Symbols
- FIGURE 1-2. Mechanical Outline Drawing
- SECTION 2 - INSTALLATION
- 2.1 Unpacking and Inspection
- 2.2 Terminations and Controls
- TABLE 2-1. Front Panel Controls, Indicators and Terminations
- FIGURE 2-1. ATE-DMG Full Rack Series Front Panel
- TABLE 2-2. Rear Panel Terminations
- FIGURE 2-2. ATE-DMG Full Rack Series Rear Panel
- TABLE 2-3. Internal Controls and Their Functions
- FIGURE 2-3. Location of Internal Controls
- TABLE 2-4. Input/Output Pin Assignments for Remote Control
- 2.3 Source Power Requirements
- FIGURE 2-4. A-C Input Source Voltage Selection, ATE-DMG Full Rack Series
- 2.4 Cooling
- 2.5 Preliminary Operational Check
- FIGURE 2-5. LCD Power On Defaults
- 2.6 Installation
- 2.6.1 Grounding
- 2.6.1.1 A-C (Safety) Ground
- 2.6.1.2 Isolation from Ground.
- 2.7 Fast Mode Conversion of the Ate Power Supply
- 2.7.1 Precautions.
- 2.7.2 Lag Network Adjustment
- 2.7.3 Crowbar Operation, Fast Mode
- 2.7.4 Manual Change-over, Slow/fast Mode
- FIGURE 2-6. Required Steps for ATE “Fast Mode” Conversion
- 2.8 Operating Configuration
- SECTION 3 - OPERATION
- 3.1 General
- 3.1.1 Safety Grounding
- 3.1.2 D-C (Output) Grounding
- 3.1.3 Power Supply/Load Interface
- 3.1.3.1 Load Wire Selection
- FIGURE 3-1. Typical Output Impedance vs. Frequency Plot for Stabilized d-c Sources
- 3.2 Load Connection
- 3.2.1 General
- FIGURE 3-2. Standard Jumper Link Connections for Local (Front Panel) Control of Output Voltage, Output Current and VP Crowbar Level (Slow Mode)
- 3.2.2 Load Connection, Method I (Local Error Sensing)
- FIGURE 3-3. Load Connection Method I, Local Error Sensing
- 3.2.3 Load Connection, Method II (Remote Error Sensing)
- FIGURE 3-4. Load Connection, Method II Using Remote Error Sensing.
- 3.2.4 Load Connection, Method III
- FIGURE 3-5. Load Connection, Method III
- 3.3 Overvoltage Crowbar, Setup and Check
- 3.3.1 Setup and Check Procedure
- 3.4 Local Mode Operation (Keypad Operation)
- 3.4.1 Front Panel Keypad and LCD
- 3.4.1.1 Command Entry Status
- 3.4.1.2 Data Entry Status
- 3.4.1.3 Display (LCD)
- 3.4.1.4 Keypad Functions
- TABLE 3-1. Key Functions (Continued)
- 3.4.2 Turning the Power Supply On
- FIGURE 3-6. LCD Power On Defaults
- 3.4.3 Setting Local Mode
- 3.4.4 Adjusting LCD Contrast
- 3.4.5 Enabling/Disabling Audible Beeps
- 3.4.6 Enabling/Disabling DC Output Power
- 3.4.7 Reset
- 3.4.8 Setting Output Voltage or Current
- 3.4.9 Setting Overvoltage or Overcurrent Protection
- 3.4.10 Changing Protection Delay
- 3.4.11 Changing Maximum Voltage or Current Value
- 3.4.12 Storing Power Supply Output Settings
- 3.4.13 Recalling Stored Output Settings
- 3.4.14 Enabling Remote Analog Control
- 3.4.15 Local Mode Programming of the Power Supply.
- 3.4.15.1 Creating or Modifying a Program (Program Edit Mode)
- 3.4.15.1.1 Modifying Programmed Time Interval
- 3.4.15.1.2 Time Interval Accuracy
- 3.4.15.1.3 Display Program Option
- 3.4.15.2 Running a Program
- 3.4.15.3 Stepping Through a Program
- 3.4.15.4 Cycling a Program
- TABLE 3-2. Memory Location Worksheet
- 3.4.15.5 Running a Program Once
- 3.4.15.6 Stopping a Program
- 3.4.15.7 Stopping a Running Program
- 3.4.15.8 Sample Program
- TABLE 3-3. Sample Program (Model ATE 25-40DMG)
- 3.4.16 Calibration
- 3.5 Analog Remote Programming
- FIGURE 3-7. A11 Assembly Connector and Pin Locations
- TABLE 3-4. Connector A11J5 Pin Functions
- 3.6 Digital Remote Mode Programming
- 3.6.1 IEEE 488 (GPIB) Bus Protocol
- TABLE 3-5. IEEE 488 (GPIB) Bus Interface Functions
- TABLE 3-6. IEEE 488 (GPIB) Bus Command Mode Messages
- TABLE 3-7. IEEE 488 (GPIB) Bus Data Mode Messages
- 3.6.2 DCL Control
- 3.6.3 Changing the GPIB Address
- 3.6.4 Enabling Remote Analog Control
- 3.6.5 Programming Techniques to Optimize performance
- 3.7 SCPI Programming
- 3.7.1 SCPI Messages
- 3.7.2 Common Commands/Queries
- 3.7.3 SCPI Subsystem Command/Query Structure
- 3.7.3.1 ABORt Subsystem
- 3.7.3.2 DIAG Subsystem
- 3.7.3.3 DISPlay Subsystem
- 3.7.3.4 INITiate Subsystem
- 3.7.3.5 LIST Subsystem
- 3.7.3.6 MEASure Subsystem
- 3.7.3.7 OUTPut Subsystem
- 3.7.3.8 Protection Subsystem
- 3.7.3.9 STATus Subsystem
- 3.7.3.10 TRIGger subsystem
- 3.7.3.11 [SOURce:]VOLTage and [SOURce:]CURRent Subsystems
- 3.7.3.12 CALibrate Subsystem
- 3.7.4 Program Message Structure
- FIGURE 3-8. Tree Diagram of SCPI Commands Used with ATE-DMG Power Supply
- 3.7.4.1 Keyword
- TABLE 3-8. Rules Governing Shortform Keywords
- FIGURE 3-9. Message Structure
- 3.7.4.2 Keyword Separator
- 3.7.4.3 Query Indicator
- 3.7.4.4 Data
- 3.7.4.5 Data Separator
- 3.7.4.6 Message Unit Separator
- 3.7.4.7 Root Specifier
- 3.7.4.8 Message Terminator
- 3.7.5 Understanding The Command Structure
- 3.7.6 Program Message Syntax Summary
- 3.7.7 SCPI Program Examples
- FIGURE 3-10. Typical Example of ATE-DMG Power Supply Program Using SCPI Commands
- APPENDIX A - IEEE 488.2 COMMAND/QUERY DEFINITIONS
- TABLE A-1. IEEE 488.2 Command/query Index
- A.2 *CLS — Clear Status Command
- A.3 *ESE — Standard Event Status Enable Command
- TABLE A-2. Standard Event Status Enable Register and Standard Event Status Register Bits
- A.4 *ESE? — Standard Event Status Enable Query
- A.5 *ESR? — Event Status Register Query
- A.6 *IDN? — Identification Query
- A.7 *OPC — Operation Complete Command
- A.8 *OPC? — Operation Complete Query
- A.9 *OPT? — Options Query
- A.10 *RCL — Recall Command
- A.11 *RST — Reset Command
- A.12 * SAV — Save Command
- FIGURE A-1. GPIB Commands
- A.13 *SRE — Service Request Enable Command
- TABLE A-3. Service Request Enable and Status Byte Register Bits
- A.14 *SRE? — Service Request Enable Query
- A.15 *STB? — Status Byte Register Query
- A.16 *TRG — Trigger Command
- A.17 *TST? — Self Test Query
- APPENDIX B - SCPI COMMAND/QUERY DEFINITIONS
- B.1 Introduction
- TABLE B-1. SCPI Subsystem Command/query Index
- B.2 ABORt Command
- FIGURE B-1. Programming the Output
- B.3 CALibrate:CURRent:LEVel Command
- B.4 CALibrate:CURRent[:DATA] Command
- FIGURE B-2. Using Calibration Commands and Queries
- B.5 CALibrate:PASSword Command
- B.6 CALibrate:SAVE Command
- B.7 CALibrate:STATus Command
- B.8 CALibrate:STATus? Query
- B.9 CALibrate:VOLTage:LEVel Command
- B.10 CALibrate:VOLTage[:DATA] Command
- B.11 CALibrate:ZERO Command
- B.12 DIAG:EXT Command
- B.13 DIAG:EXT? Query
- B.14 DISPlay:CONTrast Command
- FIGURE B-3. Using Display Commands
- B.15 DISPlay:CONTrast? Query
- B.16 DISPlay:MODE Command
- B.17 DISPlay:MODE? Query
- B.18 DISPlay:TEXT Command
- B.19 DISPlay:TEXT? Query
- B.20 INITiate[:IMMediate] Command
- B.21 INITiate:CONTinuous Command
- B.22 INITiate:CONTinuous Query
- B.23 INSTrument:STATe Command
- B.24 LIST:CURRent Command
- B.25 [SOUR:]LIST:CURRent? Query
- B.26 [SOUR:]LIST:CURRent:PROTect Command
- FIGURE B-4. Using LIST Commands and Queries
- B.27 [SOUR:]LIST:CURRent:PROTect? Query
- B.28 [SOUR:]LIST:DWELl Command
- B.29 [SOUR:]LIST:DWELl? Query
- B.30 [SOUR:]LIST:INDex Command
- B.31 [SOUR:]LIST:INDex? Query
- B.32 [SOUR:]LIST:SEQuence:NEXT Command
- B.33 [SOUR:]LIST:SEQuence:NEXT? Query
- B.34 [SOUR:]LIST:SEQuence:STARt Command
- B.35 [SOUR:]LIST:SEQuence:STARt? Query
- B.36 [SOUR:]LIST:VOLTage Command
- B.37 [SOUR:]LIST:VOLTage? Query
- B.38 [SOUR:]LIST:VOLTage:PROTect Command
- B.39 [SOUR:]LIST:VOLTage:PROTect Query
- B.40 MEASure[:SCALar]:CURRent[:DC]? Query
- B.41 MEASure[:VOLTage][:SCALar][:DC]? Query
- B.42 OUTPut[:STATe] Command
- B.43 OUTPut[:STATe] Query
- B.44 OUTPut:PROTection:DELay Command
- B.45 OUTPut:PROTection:DELay Query
- B.46 PROGram:SELect:STATe Command
- B.47 PROGram:SELect:STATe? Query
- B.48 READ[:SCALar]:CURRent[:DC]? Query
- B.49 READ[:VOLTage][:SCALar][:DC]? Query
- B.50 [SOURce:]CURRent[:LEVel][:IMMediate][:AMPlitude] Command
- B.51 [SOURce:]CURRent[:LEVel][:IMMediate][:AMPlitude] Query
- B.52 [SOURce:]CURRent:LIMit:HIGH Command
- B.53 [SOURce:]CURRent:LIMit:HIGH? Query
- B.54 [SOURce:]CURRent:[:LEVel]MODE Command
- B.55 [SOURce:]CURRent:[:LEVel]MODE? Query
- B.56 [SOURce:]CURRent:PROTection[:LEVel] Command
- FIGURE B-5. Programming Current
- B.57 [SOURce:]CURRent:PROTection[:LEVel]? Query
- B.58 [SOURce:]CURRent:PROTection:CLEar Command
- B.59 [SOURce:]CURRent:PROTection:TRIPped? Query
- B.60 [SOURce:]CURRent:[:LEVel]TRIGgered[:AMPlitude] Command
- B.61 [SOURce:]CURRent:[:LEVel]TRIGgered[:AMPlitude]? Query
- B.62 [SOURce:]VOLTage[:LEVel][:IMMediate][:AMPlitude] Command
- B.63 [SOURce:]VOLTage[:LEVel][:IMMediate][:AMPlitude]? Query
- B.64 [SOURce:]VOLTage:[:LEVel]TRIGgered[:AMPlitude] Command
- B.65 [SOURce:]VOLTage:[:LEVel]TRIGgered[:AMPlitude]? Query
- B.66 [SOURce:]VOLTage:LIMit:HIGH Command
- B.67 [SOURce:]VOLTage:LIMit:HIGH? Query
- B.68 [SOURce:]VOLTage:[:LEVel]MODE Command
- B.69 [SOURce:]VOLTage:[:LEVel]MODE? Query
- B.70 [SOURce:]VOLTage:PROTection[:LEVel] Command
- FIGURE B-6. Programming Voltage
- B.71 [SOURce:]VOLTage:PROTection[:LEVel]? Query
- B.72 [SOURce:]VOLTage:PROTection:CLEar Command
- B.73 [SOURce:]VOLTage:PROTection:TRIPped? Query
- B.74 [SOURce:]FUNCtion:MODE? Query
- B.75 STATus:OPERation:CONDition Query
- TABLE B-2. Operation Condition Register, Operation Enable Register, and Operation Event Register Bits
- B.76 STATus:OPEReration:ENABle Command
- B.77 STATus:OPEReration:ENABle? Query
- B.78 STATus:OPERation[:EVENt] Query
- B.79 STATus:PRESet Command
- FIGURE B-7. Using Status Commands and Queries
- B.80 STATus:QUEStionable[:EVENt]? Query
- TABLE B-3. Questionable Event Register, Questionable Condition Register and Questionable Condition Enable Register Bits
- B.81 STATus:QUEStionable:CONDition? Query
- B.82 STATus:QUEStionable:ENABle Command
- B.83 STATus:QUEStionable:ENABle? Query
- B.84 SYSTem:ERRor[:NEXT]? Query
- B.85 SYSTem:ERRor:CODE? Query
- B.86 SYSTem:ERRor:CODE:ALL? Query
- B.87 SYSTem:KLOCk Command
- B.88 SYSTem:KLOCk? Query
- B.89 SYSTem:LANGuage? Query
- B.90 SYSTem:LANGuage Command
- TABLE B-4. Error Messages
- B.91 SYSTem:PASSword:CENable Command
- B.92 SYSTem:PASSword:CDISable Command
- B.93 SYSTem:PASSword:STATe? Query
- B.94 SYSTem:SECurity:IMMediate Command
- TABLE B-5. Factory Default Calibration Passwords
- TABLE B-6. Master Passwords
- B.95 SYSTem:SET Command
- B.96 SYSTem:VERSion Query
- FIGURE B-8. Using System Commands and Queries
| Recognized languages: | English |
|---|---|
| Pages: | 14 |
| Size: | 565 KB |
Show table of contents
Document Outline
- 1.1 Scope of Manual
- 1.2 Description
- FIGURE 1. HSF Rear Panel Connector and RA 19-4C Rack Adapter I/O Connector
- TABLE 1. HSF Rear Connector Pin Assignments
- TABLE 2. Output Ratings and Specifications
- FIGURE 2. Power Rating Vs. Temperature
- TABLE 3. Power Supply Ratings and Specifications
- FIGURE 3. Mechanical Outline Drawing Of The HSF 300W Power Supply
- 3.1 DIP Switch Configuration
- FIGURE 4. DIP Switch Configuration
- 3.2 Front Panel Access.
- 3.3 Keying
- FIGURE 5. Front Panel Controls, Indicators and Test Points
- 3.4 Output Voltage Control
- 3.4.1 Front Panel Voltage Control
- 3.4.2 Remote Voltage Control
- FIGURE 6. DIP Switch Settings for Control of Output Voltage
- TABLE 4. Minimum Conditions for Relay, Meter and LED Operation
- FIGURE 7. Connections For Remote Voltage Control
- 3.5 Remote On-Off
- FIGURE 8. DIP Switch Settings for Using RESET button or Remote ON-OFF
- 3.6 Protection Circuits
- 3.6.1 Overvoltage And Overtemperature Protection
- 3.6.2 Overcurrent Setting and Protection
- 3.6.3 Fan Failure
- 3.6.4 Undervoltage
- 3.7 Alarm Settings
- 3.7.1 Visual Alarm.
- 3.7.2 Alarm Signals.
- 3.7.2.1 Internal Isolated Relay Alarm
- 3.7.2.2 Optically-Coupled Logical Alarm
- FIGURE 9. DIP switch settings for Optically Coupled Logical Alarm
- FIGURE 10. Output Alarm Circuit Optically Isolated
- FIGURE 11. ±PF Power Failure Optocoupler Timing Diagram
- 3.8 VDC ON/Alarm Indicator Power Options
- FIGURE 12. DIP switch settings for VDC ON/ALARM Power Options
- 3.9 Local/remote Sensing
- 3.10 Retaining Latches
| Recognized languages: | English |
|---|---|
| Pages: | 16 |
| Size: | 525 KB |
Show table of contents
Document Outline
- 1.1 Scope of Manual
- 1.2 Description
- 1.3 Options
- FIGURE 1. HSF Rear Panel Connector and RA 19-4C Rack Adapter I/O Connector
- TABLE 1. HSF Rear Connector Pin Assignments
- TABLE 2. Output Ratings and Specifications
- FIGURE 2. Power Rating Vs. Temperature (Input: 95 to 264V a-c)
- TABLE 3. Power Supply Ratings and Specifications
- FIGURE 3. Mechanical Outline Drawing Of The HSF 600W Power Supply
- 3.1 DIP Switch Configuration
- FIGURE 4. DIP Switch Configuration
- 3.2 Front Panel Access.
- 3.3 Keying
- FIGURE 5. Front Panel Controls, Indicators and Test Points
- 3.4 Output Voltage Control
- 3.4.1 Front Panel Voltage Control
- 3.4.2 Remote Voltage Control
- FIGURE 6. DIP Switch Settings for Control of Output Voltage
- TABLE 4. Minimum Conditions for Relay and LED Operation
- FIGURE 7. Connections For Remote Voltage Control
- 3.5 Remote On-Off
- FIGURE 8. DIP Switch Settings for Using RESET button or Remote ON-OFF
- 3.6 Protection Circuits
- 3.6.1 Overvoltage And Overtemperature Protection
- 3.6.2 Overcurrent Setting and Protection
- 3.6.3 Fan Failure
- 3.6.4 Undervoltage
- 3.7 Alarm Settings
- 3.7.1 Visual Alarm.
- 3.7.2 Alarm Signals.
- 3.7.2.1 Internal Isolated Relay Alarm
- 3.7.2.2 Optically-Coupled Logical Alarm
- FIGURE 9. DIP switch settings for Optically Coupled Logical Alarm
- FIGURE 10. Output Alarm Circuit Optically Isolated
- FIGURE 11. ±PF Power Failure Optocoupler Timing Diagram
- 3.8 Local/remote Sensing
- 3.9 Retaining Latches
- 5.1 Adjusting the Voltage
- 5.2 Parallel Connections, Standard and C Models