KEPCO KLP Series User Manual, Rev 4 - Manual (Page 7)

KLP SVC 020498
i
TABLE OF CONTENTS
SECTION PAGE
SECTION 1 - INTRODUCTION
1.1 Scope of Manual......................................................................................................................................... 1-1
1.2 General Description .................................................................................................................................... 1-1
1.3 Options ....................................................................................................................................................... 1-2
1.3.1 Rapid Output Discharge Circuit (RODC) Option (R Suffix) ..................................................................... 1-2
1.4 Specifications.............................................................................................................................................. 1-2
1.5 Features...................................................................................................................................................... 1-10
1.5.1 Local Control ........................................................................................................................................... 1-10
1.5.2 Remote Control ....................................................................................................................................... 1-10
1.5.2.1 Digital Programming........................................................................................................................... 1-10
1.5.2.2 Analog Programming ......................................................................................................................... 1-10
1.5.3 Digital Calibration .................................................................................................................................... 1-10
1.5.4 Overvoltage/Overcurrent Protection........................................................................................................ 1-11
1.5.5 User-defined Voltage/Current Limits (Virtual Models) ............................................................................. 1-11
1.5.6 Storage of User-Programmed Active Settings ........................................................................................ 1-11
1.5.7 User-Programmed Sequences................................................................................................................ 1-11
1.5.8 Last Setting Recall .................................................................................................................................. 1-11
1.5.9 Built-in Protection .................................................................................................................................... 1-11
1.5.10 Internal Relay .......................................................................................................................................... 1-12
1.5.11 Master/Slave Control [standard models Only]......................................................................................... 1-12
1.6 Equipment Supplied.................................................................................................................................... 1-12
1.7 Accessories ................................................................................................................................................ 1-12
1.8 Safety.......................................................................................................................................................... 1-12
SECTION 2 - INSTALLATION
2.1 Unpacking and Inspection .......................................................................................................................... 2-1
2.2 Terminations and Controls.......................................................................................................................... 2-1
2.2.1 Front Panel Controls and Indicators........................................................................................................ 2-1
2.2.2 Rear Panel Connectors and Switches..................................................................................................... 2-2
2.3 Source Power Requirements...................................................................................................................... 2-6
2.4 Cooling........................................................................................................................................................ 2-6
2.5 Preliminary Operational Check ................................................................................................................... 2-6
2.6 Installation................................................................................................................................................... 2-7
2.6.1 Rack Mounting ........................................................................................................................................ 2-7
2.7 Wiring Instructions ...................................................................................................................................... 2-7
2.7.1 Safety Grounding .................................................................................................................................... 2-8
2.7.2 Source Power.......................................................................................................................................... 2-8
2.7.2.1 Current Rating.................................................................................................................................... 2-8
2.7.2.2 Connections ....................................................................................................................................... 2-8
2.7.3 D-C Output Grounding ............................................................................................................................ 2-9
2.7.4 Power Supply/Load Interface .................................................................................................................. 2-10
2.7.5 Load Connection - General ..................................................................................................................... 2-10
2.7.5.1 Local Sensing/Remote Sensing Select .............................................................................................. 2-10
2.7.6 Series Operation ..................................................................................................................................... 2-11
2.7.7 Parallel Operation.................................................................................................................................... 2-11
2.7.7.1 Load Sharing...................................................................................................................................... 2-13
2.7.8 Master/Slave Configurations [Standard Models Only]............................................................................. 2-14
2.7.9 Analog I/O Connections .......................................................................................................................... 2-14
2.8 Digital Connections..................................................................................................................................... 2-15
2.8.1 GPIB Connections................................................................................................................................... 2-15
2.8.2 RS 232 Connections [Standard Models Only]......................................................................................... 2-15
2.8.3 LAN Connections [E-Series Models Only]............................................................................................... 2-15
SECTION 3 - OPERATION
3.1 General ....................................................................................................................................................... 3-1
3.2 Local Mode Operation ................................................................................................................................ 3-1
3.2.1 Turning the Power Supply On ................................................................................................................. 3-1