Yaskawa iQpump Drive User Manual - Manual (Page 179)

YASKAWA TM.iQp.01 iQpump Drive User Manual 179
L3-04 0492H
Stall Prevention
Selection During Decel
StallP Decel Sel
0: Disabled (The Drive decelerates at the active deceleration rate, C1-
02 or C1-04. If the load is too large or the deceleration time is too short,
an OV fault may occur.)
1: General Purpose (The Drive decelerates at the active deceleration
rate, C1-02 or C1-04, but if the main circuit DC bus voltage reaches the
stall prevention level the output frequency will clamp. Deceleration
will continue once the DC bus level drops below the stall prevention
level.)
2: Intelligent (The active deceleration rate is ignored and the Drive
decelerates as fast as possible w/o hitting OV fault level.)
0 to 3 1 Programming 102
L3-05 0493H
Stall Prevention Level
During Decel
StallP Run Sel
0: Disabled (Drive runs a set frequency.) A heavy load may cause the
Drive to trip on an OC fault.
1: Decel Time 1 (In order to avoid stalling during heavy loading, the
Drive will start to decelerate at Decel time 1 (C1-02) if the output
current exceeds the level set by L3-06. Once the current level drops
below the L3-06 level the Drive will accelerate back to its set
frequency at the active acceleration rate.)
2: Decel Time 2 (Same as setting 1 except the Drive decelerates at
Decel Time 2 (C1-04).) For 6 Hz or less frequency, stall prevention
function during run is disabled regardless of L3-05 set.
0 to 2 1 Programming 103
L3-06 0494H
Stall Prevention Level
During Running
StallP Run Level
This function is enabled when L3-05 is “1” or “2”.
Drive rated current is set as 100%.
Normally, changing the setting is not required.
Decrease the set value if stalling occurs at factory setting.
30 to 200 120% Programming 103
Ref Detection
L4-01 0499H
Speed Agreement
Detection Level
Spd Agree Level
L4-01 and L4-02 are used in conjunction with the multi-function
outputs, (H2-01and H2-02) as a setpoint and hysteresis for a contact
closure.
0.0 to
200.0
0.0 Hz Programming 104
L4-02 049AH
Speed Agreement
Detection Width
Spd Agree Width
0.0 to 20.0 2.0 Hz Programming 104
L4-05 049DH
Frequency Reference
Loss Detection Selection
Ref Loss Sel
Determines how the Drive will react when the frequency reference is
lost.
0: Stop (Disabled) - Drive will not run at the frequency reference.
1: Enabled @ % of PrevRef - Drive will run at a percentage (L4-06) of
the frequency reference level at the time frequency reference was lost.
Note: Only available in the Hand Mode (P5-01 = 0).
0 or 1 0 Programming 105
L4-06 04C2H
Frequency Reference
Level at Loss Frequency
Fref at Floss
If Frequency Reference loss function is enabled (L4-05 = 1) and
Frequency Reference is lost, then the Drive will run at reduced
frequency reference determined by L4-06. New Fref=Fref at time of
loss x L4-06.
Note: Only available in the Hand Mode (P5-01 = 0)
0 or 1 0 Programming 105
Fault Restart
L5-01 049EH
Number of Auto Restart
Attempts
Num of Restarts
Determines the number of times the Drive will perform an automatic
restart.
0 to 10 0
Pump Quick
Setup
105
L5-02 049FH
Auto Restart Operation
Selection
Restart Sel
Determines if the fault contact activates during an automatic restart
attempt.
0: No Flt Relay - fault contact will not activate during an automatic
restart.
1: Flt Relay Active - fault contact will activate during an automatic
restart.
0 or 1 0 Programming 105
L5-03 04A0H
Maximum Restart Time
After Fault
Max Restart Time
If the restart fails (or is not attempted due to a continuing fault
condition, e.g. an OV fault) the Drive waits the Maximum Restart Time
After Fault (L5-03) before attempting another restart. This parameter is
not applicable to Loss of Prime Fault.
10.0 to
3600.0
<0032>
180.0 sec
Pump Quick
Setup
105
Parameter
No.
Modbus
Address
Parameter Name
Digital Operator
Display
Description
Setting
Range
Factory
Setting
Menu
Location
Page
No.