Floor finishing (cycle 23), 8 sl c y cles – HEIDENHAIN iTNC 530 (340 49x-04) User Manual
Page 459

HEIDENHAIN iTNC 530
459
8.8 SL c
y
cles
FLOOR FINISHING (Cycle 23)
The tool approaches the machining plane smoothly (on a vertically
tangential arc) if there is sufficient room. If there is not enough room,
the TNC moves the tool to depth vertically. The tool then clears the
finishing allowance remaining from rough-out.
Feed rate for plunging
Q11: Traversing speed of the
tool during penetration.
Feed rate for roughing
Q12: Traversing speed for
milling.
Retraction feed rate
Q208: Traversing speed of the
tool in mm/min when retracting after machining. If
you enter Q208 = 0, the TNC retracts the tool at the
feed rate in Q12.
Example: NC blocks
60 CYCL DEF 23 FLOOR FINISHING
Q11=100
;FEED RATE FOR PLUNGING
Q12=350
;FEED RATE FOR ROUGHING
Q208=99999
;RETRACTION FEED RATE
X
Z
Q11
Q12
Before programming, note the following
The TNC automatically calculates the starting point for
finishing. The starting point depends on the available
space in the pocket.
- TNC 122 User Manual (63 pages)
- TNC 122 Technical Manual (70 pages)
- TNC 360 Service Manual (157 pages)
- TNC 416 Technical Manual (510 pages)
- TNC 335 Technical Manual (581 pages)
- TNC 360 User Manual (237 pages)
- TNC 360 ISO-Programmierung (2 pages)
- TNC 415 (280 540) User Manual (227 pages)
- TNC 370D (92 pages)
- TNC 416 (289 pages)
- TNC 415 (280 540) Technical Manual (752 pages)
- TNC 415 (259 96x) Service Manual (195 pages)
- TNC 407 (280 580) User Manual (376 pages)
- iTNC 530 (340 420) Pilot (104 pages)
- TNC 407 (280 580) ISO Programming (333 pages)
- TNC 415 (280 540) Service Manual (252 pages)
- PT 880 Installation (112 pages)
- ND 100 User Manual (116 pages)
- ND 287 User Manual (147 pages)
- ND 280 Quick Start (12 pages)
- ND 200 (156 pages)
- ND 282 (10 pages)
- ND 287 Quick Start (26 pages)
- ND 282 B (39 pages)
- ND 281 A (44 pages)
- ND 281 B v.1 (53 pages)
- ND 281 B v.2 (65 pages)
- ND 221 v.2 (10 pages)
- ND 231 B v.2 (56 pages)
- ND 231 B v.1 (44 pages)
- ND 221 B v.2 (45 pages)
- ND 550 v.2 (8 pages)
- NDP 560 (10 pages)
- ND 523 (93 pages)
- ND 570 (8 pages)
- ND 750 v.2 (46 pages)
- ND 760 v.3 (72 pages)
- ND 770 v.1 (40 pages)
- ND 770 v.3 (41 pages)
- ND 760 E (44 pages)
- IOB 49 (21 pages)
- NDP 960 (68 pages)
- ND 780 Installation (132 pages)
- ND 970 (47 pages)
- ND 1100 Quick Start (36 pages)