BECKHOFF ET1100 - Manual (Page 18)

Features and Registers
III-4 Slave Controller – ET1100 Hardware Description
2 Features and Registers
2.1 Features
Table 4: ET1100 Feature Details
Feature
ET1100
-0003
EtherCAT Ports 2-4
Permanent ports 2-4
Optional Bridge port 3 (EBUS or MII) -
EBUS ports 0-4
MII ports 0-4
RMII ports -
RGMII ports -
Port 0 -
Ports 0, 1 x
Ports 0, 1, 2 x
Ports 0, 1, 3 x
Ports 0, 1, 2, 3 x
Slave Category Full Slave
Position addressing x
Node addressing x
Logical addressing x
Broadcast addressing x
Physical Layer General Features
FIFO Size configurable (0x0100[18:16]) x
FIFO Size default from SII EEPROM -
Auto-Forwarder checks CRC and SOF x
Forwarded RX Error indication, detection
and Counter (0x0308:0x030B)
x
Lost Link Counter (0x0310:0x0313) x
Prevention of circulating frames x
Fallback: Port 0 opens if all ports are
closed
x
VLAN Tag and IP/UDP support x
Enhanced Link Detection per port
configurable
-
EBUS Features
Low Jitter x
Enhanced Link Detection supported -
Enhanced Link Detection compatible x
EBUS signal validation x
LVDS Transceiver internal x
LVDS sample rate [MHz] 1,000
Remote link down signaling time
configurable 0x0100[22]
x
General Ethernet Features (MII/RMII/RGMII)
MII Management Interface
(0x0510:0x051F)
x
Supported PHY Address Offsets 0/16
Individual port PHY addresses -
Port PHY addresses readable -
Link Polarity configurable x
Enhanced Link Detection supported x
FX PHY support (native) -
PHY reset out signals -
Link detection using PHY signal (LED) x
MI link status and configuration -
MI controllable by PDI (0x0516:0x0517) -
MI read error (0x0510.13) -
MI PHY configuration update status
(0x0518.5)
-
MI preamble suppression -
Additional MCLK x
Gigabit PHY configuration -
Gigabit PHY register 9 relaxed check -
FX PHY configuration -
Transparent Mode x
Feature
ET1100
-0003
MII Features
CLK25OUT as PHY clock source x
Bootstrap TX Shift settings x
Automatic TX Shift setting (with TX_CLK) -
TX Shift not necessary (PHY TX_CLK as
clock source)
-
FIFO size reduction steps 1
PDI General Features
Increased PDI performance -
Extended PDI Configuration
(0x0152:0x0153)
x
PDI Error Counter (0x030D) x
PDI Error Code (0x030E) -
CPU_CLK output (10, 20, 25 MHz) x
SOF, EOF, WD_TRIG and WD_STATE
independent of PDI
-
Available PDIs and PDI features
depending on port configuration
x
PDI selection at run-time (SII EEPROM) x
PDI active immediately (SII EEPROM
settings ignored)
-
PDI function acknowledge by write -
PDI Information register 0x014E:0x014F -
Digital I/O PDI x
Digital I/O width [bits] 8/16/24/32
PDI Control register value
(0x0140:0x0141)
4
Control/Status signals: 7/0 1
LATCH_IN x 1
SOF x 1
OUTVALID x 1
WD_TRIG x 1
OE_CONF x 1
OE_EXT x 1
EEPROM_
Loaded
x 1
WD_STATE -
EOF -
Granularity of direction configuration [bits] 2
Bidirectional mode x
Output high-Z if WD expired x
Output 0 if WD expired x
Output with EOF x
Output with DC SyncSignals x
Input with SOF x
Input with DC SyncSignals x
1 Availability depending on port configuration