Artesyn MVME51005E SBC Installation and Use (July 2014) - Manual (Page 107)

Pin Assignments
MVME51005E Single Board Computer Installation and Use (6806800A38D) 109
6.3.5 VMEbus Connectors P1 & P2 Pin Assignments (PMC mode)
The VMEbus connector P1 provides power and VME signals for 24-bit address and 16-bit data.
The pin assignments for the connector are specified by the IEEE P1014-1987 VMEbus
Specification and the VME64 Extension Standard.
Row B of connector P2 provides power to the MVME5100, and to the upper eight VMEbus
address lines, and additional 16 VMEbus data lines. Rows A, C, Z and D provide power and
interface signals to the MVME762 transition module. The pin assignments for connector P2 in
PMC mode are as follows:
Table 6-7 Pin Assignments for Connector P2 in PMC Mode
Pin Row Z Row A Row B Row C Row D
1 PMC2_2 (J24-2) PMC1_2 (J14-2) +5V PMC1_1 (J14-1) PMC2_1 (J24-1)
2 GND PMC1_4 (J14-4) GND PMC1_3 (J14-3) PMC2_3 (J24-3)
3 PMC2_5 (J24-5) PMC1_6 (J14-6) RETRY# PMC1_5 (J14-5) PMC2_4 (J24-4)
4 GND PMC1_8 (J14-8) VA24 PMC1_7 (J14-7) PMC2_6 (J24-6)
5 PMC2_8 (J24-8) PMC1_10 (J14-10) VA25 PMC1_9 (J14-9) PMC2_7 (J24-7)
6 GND PMC1_12 (J14-12) VA26 PMC1_11 (J14-11) PMC2_9 (J24-9)
7 PMC2_11(J24-
11) PMC1_14 (J14-14) VA27 PMC1_13 (J14-13) PMC2_10 (J24-10)
8 GND PMC1_16 (J14-16) VA28 PMC1_15 (J14-15) PMC2_12 (J24-12)
9 PMC2_14 (J24-
14) PMC1_18 (J14-18) VA29 PMC1_17 (J14-17) PMC2_13 (J24-13)
10 GND PMC1_20 (J14-20) VA30 PMC1_19 (J14-19) PMC2_15 (J24-15)
11 PMC2_17 (J24-
17) PMC1_22 (J14-22) VA31 PMC1_21 (J14-21) PMC2_16 (J24-16)
12 GND PMC1_24 (J14-24) GND PMC1_23 (J14-23) PMC2_18 (J24-18)
13 PMC2_20 (J24-
20) PMC1_26 (J14-26) +5V PMC1_25 (J14-25) PMC2_19 (J24-19)
14 GND PMC1_28 (J14-28) VD16 PMC1_27 (J14-27) PMC2_21 (J24-21)
15 PMC2_23 (J24-
23) PMC1_30 (J14-30) VD17 PMC1_29 (J14-29) PMC2_22 (J24-22)
16 GND PMC1_32 (J14-32) VD18 PMC1_31 (J14-31) PMC2_24 (J24-24)