EXFO VDSL2 - Manual (Page 265)

Technical Specifications
Copper, VDSL2, ADSL2+ and IP Triple-Play Test Set 257
pp g p
NOTES a. At 23 °C ± 1 °C on batteries, unless otherwise specified.
b. Characteristics are subject to instrument noise floor (approx. – 70 dBm). Levels below – 70 dBm can be measured using the PSD noise test.
c. Does not include the uncertainty due to VOP.
RECEIVER CHARACTERISTICS b
Receive frequency 200 Hz to 10 kHz, resolution 1 Hz
Receive frequency 10 kHz to 20 kHz, resolution 10 Hz
Receive frequency 20 kHz to 30 MHz, resolution 1 kHz
Frequency uncertainty (accuracy) ±(50 ppm + 0.5 Hz)
Receive level (dBm) –90 to +10 at 100 Ÿ or 135 Ÿ, resolution 0.1 dB
–100 to +10 at 600 Ÿ, resolution 0.1 dB
Level uncertainty (accuracy) ±1.0 dB for 200 Hz to 20 kHz at 0 dBm
±1.0 dB for 20 kHz to 30 MHz at 0 dBm
Impedance ( Ÿ) 100, 135, 600 and bridging (100 k Ÿ)
TRANSMITTER CHARACTERISTICS
Transmit frequency 200 Hz to 20 kHz, resolution 1 Hz steps
Transmit frequency 20 kHz to 30 MHz, resolution 1 kHz steps
Transmit level (dBm) –20 to +5 at 600 Ÿ for 200 Hz to 499 Hz
–20 to +10 at 600 Ÿ for 500 Hz to 20 kHz
–10 to +10 at 100/135 Ÿ for 20 kHz to 30 MHz
Frequency uncertainty (accuracy) ±(50 ppm + 0.5 Hz)
Level uncertainty (accuracy) ±0.6 dB 200 Hz to 20 kHz at 0 dBm
±1 dB 20 kHz to 2.2 MHz
±2 dB 2.2 MHz to 17 MHz
±3 dB 17 MHz to 30 MHz
Impedance ( Ÿ) 100, 135 and 600
VF NOISE MEASUREMENT
Range (dBm) 0 to –90, subject to instrument noise floor
Uncertainty (accuracy) (dB) ±1
Filters None, 3 kHz flat, C-message, psophometric, notched and D filter (IEEE 743-1995)
VF IMPULSE NOISE
Low threshold (dBm) 0 to –40, in 1 dB steps
Mid threshold Low threshold plus separation
High threshold Mid threshold plus separation
Separation (dB) 1 to 6, in 1 dB steps
Dead time (ms) 125
Filters None, 3 kHz flat, C-message, psophometric, notched and D filter (IEEE 743-1995)
Counter Maximum 999 for each threshold
Timer 1 minute to 24 hours, default is 15 minutes
POWER INFLUENCE (NOISE TO GROUND)
Noise range (dBm) –60 to +10
Uncertainty (accuracy) (dB) ±1.0
Level uncertainty (accuracy) (dB) ±1.0 at –60 dBm
VF LONGITUDINAL BALANCE
Frequency (Hz) 1004
Frequency uncertainty (accuracy) (ppm) ±50
Level range (dB) 0 to 80
Level uncertainty (accuracy) (dB) ±1
TIME-DOMAIN REFLECTOMETRY (TDR)
Mode Fully automatic operation with location of most significant events
Distance range (m) 8 to 6000 (25 ft up to 20 000 ft)
Pulse width 15 ns to 20 —s
Test signals Sine wave, compensated sine wave, half-sine wave and square wave
Amplitude 7.5 V p-p on cable, 9 V p-p open circuit
Velocity of propagation (VOP) 0.400 to 0.999 or 120 m/ —s to 299 m/—s
Distance uncertainty c (accuracy) (m) ±(1.4 m + 2 % x distance) or ±(4.5 ft + 2 % x distance)
Units Feet and meters
Horizontal scale (m) Automatic or 30 (100 ft), 300 (1000 ft), 600 (2000 ft), 1500 (5000 ft), 3000 (10 000 ft), 6000 (20 000 ft),
13 500 (45 000 ft) and 15 000 (50 000 ft)
FREQUENCY-DOMAIN REFLECTOMETRY (FDR)
Distance range (m) 1.5 to 5000 (5 ft to 18 000 ft)
Velocity of propagation (VOP) 0.400 to 0.999 or 120 m/ —s to 299 m/—s
Distance uncertainty (accuracy) (m) ±3 (3 to 1000), ±15 (1000 to 1500), ±50 (1500 to 5000)
Units Feet and meters
LOAD COIL DETECTION
Count Five
Plot (kHz) Up to 10
Distance range (m) Up to 8000 (up to 27 000 ft)
SINGLE-END FREQUENCY RESPONSE (ATTENUATION)
Distance range (m) 70 to 5000 (200 ft to 16 000 ft)
Frequency range 4.3 kHz to 30 MHz
Frequency uncertainty (accuracy) ±50 ppm
Level uncertainty (accuracy) (dB) 2 dB, 4 dB at 30 MHz
Resolution (dB) 0.1
Horizontal scale (MHz) ADSL2+ = 2.208, VDSL2-12 = 12, VDSL2-17 = 17.66, VDSL2-30 = 30
Vertical scale (dB) 0 to +100