TeeJet Matrix 840G User Manual - Manual (Page 38)

www.teejet.com
60
●
98-05141 R2
61
●
Figure 3-14: Mark A and B Points
mph acres
1.20 10.5 Mark A
mph acres
2.60 10.5 Mark B
The console will begin providing navigation
information.
Figure 3-15: Straight A-B Guidance
Swath acres
3.57 0
0.0
NOTE: A compass is displayed during perspective
view (the ZOOM IN BUTTON or ZOOM
IN ICON is used to display the horizon).
A+ Nudge Feature
The A+ Nudge feature allows the existing A-B
guideline to be shifted to the vehicle’s current
location.
1. Press A+ NUDGE ICON
A to establish the new
guideline.
Figure 3-16: A+ Nudge
Swath acres
3.80 -2
5.1
Swath acres
3.81 -2
0.0
Curved A-B Guidance
Curved A-B Guidance provides guidance along
curved lines based on an initial A-B reference line.
This initial baseline is used to calculate all other
guidelines.
Activate Curved A-B Guidance
1. Press the screen to activate the icons and select
the GUIDANCE MODE ICON .
2. Select CURVED A-B GUIDANCE .
◄Status Bar Icon will change to .
Figure 3-17: Guidance Mode Selection
Swath acres
0.0 0
0.0
Marking A and B Points
1. Drive to the desired location of Point A .
2. While the vehicle is in motion, press MARK A
ICON A .
3. Drive to the desired location of Point B .
4. Press the MARK B ICON
B to establish the A-B
line.
NOTE: The MARK B ICON B is not available for
selection (grayed out) until the minimum
distance is traveled (9.84 ft / 3.0 m).
Use CANCEL MARK ICON to cancel the Mark A
command and revert to the previous A-B guideline
(when established).
Vehicle View
To access the Vehicle View screen.
1. Press HOME BUTTON or press the screen
to activate the icons and select HOME ICON
in bottom left corner of screen.
2. Select VEHICLE VIEW from Home Menu
.
Figure 3-12: Home Menu
Swath acres
0.0 0
0.0
Guidance Mode Select
Guidance Modes include Straight A-B ,
Curved A-B , Circle Pivot , Last Pass ,
and No Guidance Mode .
Guidance with SmartCable or SDM
• Turn the controller master switch to the “On”
position. The individual boom section switches
should remain in the “Off” position.
• Activate BoomPilot. See BoomPilot section
for details.
• In areas where application is not desired,
manually turn “off” the rate controller master
switch to shut off the booms. Turn the master
switch “on” to resume application.
NOTE: This does not apply unless a SmartCable or
SDM is installed on the system.
Straight A-B Guidance
Straight A-B guidance provides straight line
guidance based on A and B reference points. The
original A and B points are used to calculate all other
parallel guidelines.
Activate Straight A-B Guidance
1. Press the screen to activate the icons and select
the GUIDANCE MODE ICON .
2. Select STRAIGHT A-B GUIDANCE .
◄Status Bar Icon will change to .
Figure 3-13: Guidance Mode Selection
Swath acres
0.0 0
0.0
Marking A and B Points
1. Drive to the desired location of Point A .
2. While the vehicle is in motion, press MARK A
ICON A .
3. Drive to the desired location of Point B .
4. Press the MARK B ICON
B to establish the A-B
line.
NOTE: The MARK B ICON B is not available for
selection (grayed out) until the minimum
distance is traveled (9.84 ft / 3.0 m).
Use CANCEL MARK ICON to cancel the Mark A
command and revert to the previous A-B guideline
(when established).