Rockwell Automation 8520-9API 9/Series OCI API Developer's Guide User Manual
Page 245
Index
I–5
Publication 8520Ć6.6 - August 1999
PORT_BAUD_RATE, 4-21
PORT_COMMUNICATION_FORMAT,
PORT_DATA_BITS, 4-25
PORT_PARITY, 4-23
PORT_STOP_AT_PROGRAM_END,
PORT_STOP_BITS, 4-24
PORT_TIMEOUT_VALUE, 4-29
RX_CHAR_PORTA, 4-30
RX_CHAR_PORTB, 4-30
Communication Port Parameters
DEVICE_ON_PORTA, A-3
DEVICE_ON_PORTB, A-3
HARDWARE_STATUS_PORTB, A-3
HARDWARE_SUPPORT_PORTA, A-3
LEVEL_2_STATUS_PORTA, A-3
LEVEL_2_STATUS_PORTB, A-3
PORT_BAUD_RATE, A-3
PORT_COMMUNICATION_FORMAT,
PORT_DATA_BITS, A-3
PORT_PARITY, A-3
PORT_STOP_AT_PROGRAM_END,
PORT_STOP_BITS, A-3
PORT_TIMEOUT_VALUE, A-3
RX_CHAR_PORTA, A-3
RX_CHAR_PORTB, A-3
TX_CHAR_PORTB, A-3
UART_A_BUSY_STATUS, A-3
UART_B_BUSY_STATUS, A-3
Communications
ACTIVATE_RIO_PASSTHROUGH, B-2
AUX_COM_ABORT_COMMAND, B-2
AUX_COM_BACKUP_CONFIG_TABLE,
AUX_COM_CMDTBL_FROM_FLASH,
AUX_COM_CMDTBL_TO_FLASH, B-2
AUX_COM_CONFIG_FROM_FLASH,
AUX_COM_CONFIG_TO_FLASH, B-2
AUX_COM_HOST_WRITE_TO_FLASH,
COPY_DEVICE_SETUP_DEFAULTS,
DEACTIVATE_RIO_PASSTHROUGH,
ENTER_SERIAL_IO_MONITOR_MODE,
EXIT_SERIAL_IO_MONITOR_MODE,
INITIALIZE_DEVICE_SETUP, B-2
REPEAT_TX_SERIAL_IO, B-2
SAVE_DEVICE_SETUP, B-2
START_SERIAL_IO_MONITOR, B-2
STOP_SERIAL_IO_MONITOR, B-2
Constants, screen names, 3-7
Control CNC Commands, 5-23
Control Type Attribute, 4-8
Controlling OCI Station, 4-2
CONTROLLING_OCI, A-7
CONTROLLING_SPINDLE_NUM, 4-60
COPY_DEVICE_SETUP_DEFAULTS,
COPY_FROM_TYPE Enumeration, 6-4
COPY_MEM_TO_MEM, 5-39, B-4, B-6
COPY_MEM_TO_PORTA, 5-40, B-4, B-6
COPY_MEM_TO_PORTA/B Enumeration,
COPY_MEM_TO_PORTB, 5-40, B-4, B-6
COPY_OFFSET, 5-31, B-3
COPY_PART_PROGRAM, 5-38, B-4, B-5
COPY_PART_PROGRAM_FOR_EDIT,
COPY_PORTA/B_TO_MEM Enumeration,
COPY_PORTA_TO_MEM, 5-41, B-4, B-6
COPY_PORTB_TO_MEM, 5-42, B-4, B-6
COPY_TO_TYPE Enumeration, 6-4
COPYRIGHT_DATE, 4-38, A-7
CURRENT_DRESSER_RPM, A-6
CURRENT_SCALE_FACTORS, A-12