Aleft hand side (sprocket side) lh side – MTS SWIFT 10 MC Sensor User Manual
Page 131
THE INFORMATION AND DESIGN(S)
DISCLOSED HEREIN ARE CONFIDENTIAL
AND THE PROPERTY OF MTS SYSTEMS
CORPORATION AND MAY NOT BE USED,
REPRODUCED OR DISCLOSED IN ANY
FORM EXCEPT AS GRANTED IN WRITING
BY MTS SYSTEMS CORPORATION. THIS
RESTRICTION EXCLUDES INFORMATION
THAT IS IN THE PUBLIC DOMAIN OR
WAS LEGITIMATELY IN THE PRIOR
POSSESSION OF THE RECIPIENT.
PROPRIETARY DATA
SOURCE/REF
DRAWING
MATERIAL DESCRIPTION
MATERIAL SIZE
FINISH
MASK
M
THREAD DEPTHS ARE TO MIN FULL THDS
DRILL DEPTHS ARE TO FULL DIA
REMOVE BURRS AND SHARP EDGES
DO NOT SCALE PRINT
SCALE
MACHINED
SURFACES
180
UNLESS OTHERWISE SPECIFIED
.XXX HOLE SIZE TOLERANCE
0.000
TO .750
+.010/-.002
OVER .750
TO 1.500
+.015/-.003
ANGLE 2
G
E
N
E
R
A
L
T
OL
E
R
A
N
C
E
S
X
Y
.X
.XX
.XXX
THIRD
ANGLE
PROJ
C
MTS SYSTEMS CORPORATION
EDEN PRAIRIE, MINNESOTA U.S.A.
1/4
.1
.03
.010
DRAWN
CHECK
ENGR
DATE
MFG
DATE
DATE
DATE
SIZE
TITLE
NEXT LEVEL
PRODUCT CODE
NUMBER
SHEET
OF
REV
D
REVISIONS
DATE
ENGR
DRAWN
L
E
T
T
E
R
E
C
N
N
O
DESCRIPTION
m
3
2
1
NOTES:
ALIGN OUTER HUBS (ITEMS 2 & 3) ON PROPER SIDE OF RIM AND WITH STAMPINGS ("1L" & "1R")
LOCATED AT BEAM 1 ON TRANSDUCER (ITEM 1).
ASSEMBLE BOTH OUTER HUBS (ITEMS 2 & 3). APPLY MOLYKOTE GN PASTE TO THREADS AND
UNDER THE HEADS OF M6 X 1MM TORX BUTTON HEAD CAPSCREWS (ITEM 16) AND TORQUE IN
2 STEPS OF 14 & 28 FT-LB (19 N-M & 38 N-M). (USE BOLT TORQUE SEQUENCE PROCEDURE
P/N 700-003-829.)
ASSEMBLE OUTER HUBS TO RIM (ITEM 7). PROPERLY ALIGN RIM AND LACE USING SPOKES
(ITEM 6) AND FASTEN TO RIM WITH SPOKE NIPPLES (ITEM 23). TIGHTEN SPOKE NIPPLES TO
FINGER TIGHT. RIM WILL BE TRUED FOR LATERAL & RADIAL RUNOUT LATER IN ASSEMBLY.
RLJ
RAM
7-07
7-07
1
5
1/2
100-174-333
RIM ASSEMBLY-REAR,
19 X 2.15, SWIFT 10
C
11-07
RAM
RLJ
ADDED SHEETS 2-5, BALLOONS
AND NOTES.
B
R
U
L
E
1
C
ADDED PLUG SEAL, ITEM 28,
P/N 100-198-825.
R
U
L
E
1
7-08
RLJ
RAM
4.970
126.24
2.165
55
2.485
63.12
1.083
27.50
SECTION A-A
SCALE 1 : 1.75
1
2
3
7
TRANSDUCER ASSY
OUTER
HUB
OUTER
HUB
STOCK RIM
2
2
3
3
3
30 O-RING
A
A
LEFT HAND SIDE
(SPROCKET SIDE)
LH
SIDE
1L
LEFT HAND OUTER HUB IS
STAMPED WITH "1L" TO BE
LOCATED AT BEAM 1 ON TRANSDUCER
6
36
23
REF
MODIFIED STRAIGHT SPOKES
W/STOCK SPOKE NIPPLES
1
RIGHT HAND SIDE
(BRAKE SIDE)
RH
SIDE
OUTER HUB ASSY
16
40
M8 X 1.25MM TORX PAN HD SCR
(20 THIS SIDE, 20 OPP. SIDE)
1R
RIGHT HAND OUTER HUB IS
STAMPED WITH "1R" TO BE
LOCATED AT BEAM 1 ON TRANSDUCER
1
2
3