Liquid Controls SP4000 - Manual (Page 91)

88
SP4000 Flow Computer
COMMUNICATION
6.13
COMMUNICATION
(Continued)
This is a diagnostic cell for the TWP transceiver. The display shows
Clip (CLP) Progress. This is a diagnostic cell which tracks progress
of two way paging data exchange. If problems are encountered
during use, note the stage at which problems occurred prior to
seeking technical help.
Display: -124xm Ocur 54stg
CLP PROGRESS
CLP PROGRESS
(Pager)
0) IDLE
1) WAITING FOR GET MESSGE STATUS
2) WAITING TO REQUEST DIR INFO
3) RECIEVING DIR INFO
4) MAKE A REQUEST FOR MESSAGE
5) START MESSAGE DOWNLOAD
6) WAIT TO REPLY TO A MESSAGE
7) WAIT TO SEND FINAL ACK
8) INTIALIZE XMODEM
9) PARSE DATA
10) SEND RESPONSE
11)WAIT HERE UNTIL ALL BLOCKS ARE
SENT AND THEN ACK
12)WAIT FOR FINAL ACK
13)WAIT FOR TRANSMISSION TO START and
get status
14) WAIT FOR SKYTEL RESPONSE AND GET
STATUS
15) WHEN STATUS IS IN CHECK IF GOOD
then delete OR REPEAT
16)when delete done reset
20)INTIALIZE XMODEM
21)PARSE PRINT LIST DATA
22) SEND XMODEM BLOCK
23) WAIT HERE FOR ALL XMODEM TO BE
SENT
24)WAIT FOR EOT TO BE ACKNOWLEDGE
25)WAIT FOR TRANSMISSON TO START and
get status
26) WAIT FOR SKYTEL TO RESPOND and get
status
27) IF TRANSMISSION IS GOOD END ELSE
REPEAT.
30)INTIALIZE XMODEM
31)PARSE PRINT MAINTENCE DATA
32) SEND XMODEM BLOCK
33) WAIT HERE FOR ALL XMODEM TO BE
SENT
34)WAIT FOR EOT TO BE ACKNOWLEDGE
35)WAIT FOR TRANSMISSON TO START and
get status
36) WAIT FOR SKYTEL TO RESPOND and get
status
37) IF TRANSMISSION IS GOOD END ELSE
REPEAT.
40)INTIALIZE XMODEM
41)PARSE PRINT SETUP DATA
42) SEND XMODEM BLOCK
43) WAIT HERE FOR ALL XMODEM TO BE SENT
44)WAIT FOR EOT TO BE ACKNOWLEDGE
45)WAIT FOR TRANSMISSON TO START and get
status
46) WAIT FOR SKYTEL TO RESPOND and get status
47) IF TRANSMISSION IS GOOD END ELSE REPEAT.
50) MODEM STRING FOR SELF CONTACT
51)SEND STRING
52) WAIT FOR ACK SEND EOT OR REPEAT
53)WAIT FOR FINAL ACK
54)WAIT FOR TRANSMISSION TO START AND GET
STATUS
55)WAIT FOR SKYTEL RESPONSE AND GET STATUS
56)WAIT FOR STATUS INFO TO BE RECIEVED THEN
CHECK IF GOOD
57)WAIT FOR SKYTEL MESSAGE
58) WAITING FOR GET MESSGE STATUS
59) WAITING TO REQUEST DIR INFO
60) RECIEVING DIR INFO
61) DELETE MESSAGE
62) RESET CLP
70)INTIALIZE XMODEM
71)PARSE PRINT SETUP DATA
72) SEND XMODEM BLOCK
73) WAIT HERE FOR ALL XMODEM TO BE SENT
74)WAIT FOR EOT TO BE ACKNOWLEDGE
75)WAIT FOR TRANSMISSON TO START and get
status
76) WAIT FOR SKYTEL TO RESPOND and get status
77) IF TRANSMISSION IS GOOD END ELSE REPEAT.
80)INTIALIZE XMODEM
81)PARSE PRINT SETUP DATA
82) SEND XMODEM BLOCK
83) WAIT HERE FOR ALL XMODEM TO BE SENT
84)WAIT FOR EOT TO BE ACKNOWLEDGE
85)WAIT FOR TRANSMISSON TO START and get
status
86) WAIT FOR SKYTEL TO RESPOND and get status
87) IF TRANSMISSION IS GOOD END ELSE REPEAT.
100)RESETING OF THE OF CLP STAGE
101)UNIT IS LOST TRY TO RESYNC.
102) POWER UP DELAY
STG DEFINITIONS