Extron Electronics Annotator User Guide User Manual
Page 55
Command
ASCII command
(host to processor)
Response
(processor to host)
Additional description
Aux Scaler Board
Output scaler rate
Set output rate
E
X
X2!
*
X2@
Rate
}
RateX
X2!
*
X2@]
Select output resolution and refresh
rate.
View output rate
E
XRate
}
X2!
*
X2@]
Show selected output rate.
Output sync polarity
Set polarity
E
X
X2#
OPOL
}
OpolX
X2#]
Set polarity for scaler ouput.
View polarity setting
E
XOPOL
}
X2#]
Show current output polarity.
Output sync format
Set format
E
X
X2$
OSYN
}
OsynX
X2$]
Set output sync format.
View sync setting
E
XOSYN
}
X2$]
Show current output sync format.
Aspect Ratio mode
Enable Fill mode
E
X1Aspr
}
AsprX1
]
Set aspect ratio to Fill.
Enable Follow mode
E
X2Aspr
}
AsprX2
]
Set aspect ratio to Follow (default).
View aspect ratio setting
E
XAspr
}
X5%]
Show current aspect ratio.
Detail filter
Set detail level
E
X
X1%
HDET
}
HdetX
X1%]
Specify the detail (sharpness) level
to
X1%
.
Increment up
E
X+HDET
}
HdetX
X1%]
Increase the detail level.
Increment down
E
X–HDET
}
HdetX
X1%]
Decrease the detail level.
View detail value
E
XHDET
}
X1%]
Show the detail setting.
Test pattern
NOTE:
Test pattern on aux scaler board are color bars, 4x4 crosshatch, grayscale, ramp, alternating pixels, and crop.
Set the test pattern
E
XTest
X2)}
TestX
X2)]
Set test pattern to
X2)
.
View test pattern
E
XTest
}
X2)]
View the test pattern.
NOTE:
X1%
= Detail filter level, 0 to 127
X2) = Test patterns for Scaler board: 0 = Off (default), 1 = Color bars, 2 = Crosshatch, 3 = 4x4 Crosshatch,
4 = Grayscale, 5 = Ramp, 6 = Alternating Pixels, 8 = Crop
X2!
= Aux scaler resolution,
1 = 640x480
8 = 1280x1024
14 = 1600x1200
20 = 1440x900
2 = 800x600
9 = 1360x765
15 = 480p
21 = 1680x1050
3 = 852x480
10 = 1365x768
16 = 576p
22 = 1280x800
4 = 1024x768
11 = 1365x1024
17 = 720p
23 = 1080p Sharp
5 = 1024x852
12 = 1366x768
18 = 1080i
24 = 1920x1200
6 = 1024x1024
13 = 1400x1050
19 = 1080p
25 =1080p CVT
7 = 1280x768
X2@
= Aux scaler refresh rate,1 = 50 Hz, 2 = 60 Hz,
3 = 72 Hz (75 Hz for 1440x900, 24 Hz for 1080p),
4 = 96 Hz, 5 = 100 Hz, 6 = 120 Hz, 7 = 59.94 Hz
X2#
= Output polarity; 0 = H-/V- (default), 1 = H-/V+, 2= H+/V-, 3 = H+/V+
X2$
= Aux scaler output sync format, 0 = RGBHV, 1 = RGsB, 2 = YUV bi-level, 3= YUV tri-level
X5%
= Aspect ratio, 1 = Follow, 2 = Fill
Annotator • SIS Communication and Control
49