Extron Electronics Annotator User Guide - Manual (Page 23)

Edit Comm Settings (hidden)
To display and enter this menu, press and hold the Detail and Color/Tint buttons
simultaneously and then press Next. The hidden menu appears.
This menu allows the user to edit the following serial and IP settings:
Serial port baud rate, DHCP mode, IP address, subnet mask, and gateway address.
Exit Menu
At this menu pressing Next exits the menu system and returns to the default cycle.
Figure 9. Annotator Menu System Overview
Input
Configuration
Input #x
RGB
Rotate to select
video input type.
Next
Input #x
Film Detect On
Rotate to turn
Film Detect on
or off.
Next
Input #x
Vert Start 128
Rotate to adjust
Vertical Start value.
Input #x
Horz Start 128
Rotate to adjust
Horizontal Start value.
Input #x
Pixel Phase 28
Rotate to adjust
Pixel Phase value.
Input #x
Total Pix *2200
Rotate to adjust
Total Pixel value
(* = default).
Input #x
Active Pixels *1920
Rotate to adjust
Active Pixels value
(* = default).
Input #x
Active Lns *1080
Rotate to adjust
Active Lines value
(* = default).
User
Presets
Recall Preset
Next
Rotate either to
select a preset to
recall settings.
<02>
Save Preset
Next
Rotate either
to select a preset
to save current
settings to.
Menu Menu Output
Configuration
Rotate to adjust
Resolution value
Rotate to adjust
Refresh rate.
Resol 1024x768
Refresh 60.00Hz
Next
Output Type
RGBHV
Next
Sync Polarity
H Neg V Pos
Rotate either to
adjust Output
type value.
Rotate either to
adjust Sync
Polarity values.
Next Next
Next
Next
Next
Next
Next
Menu Advanced
Configuration
Auto Image
Input #x Off
Rotate to turn
Auto Image mode
On or Off.
Next
Menu
Serial Port
9600 RS232
DHCP Mode
On
MAC Address
005A6003C24
This is set at the factory
and cannot be changed
in “Edit Comm Settings”
menu.
IP Address
192.168.254.254
Gateway Address
000.000.000.000
Subnet Mask
255.255.000.000
View Comm
Settings
Exit Menu
Press NEXT
Menu
Next
Next
Next
Next
Next
Next
Auto Memories
On
Rotate either to turn
Auto Memories On
or Off.
Next
Serial Port
9600 RS232
Edit Comm
Settings
Rotate to select
RS-232 or RS-422
mode. Rotate to
change baud rate.
DHCP Mode
Rotate either to turn
DHCP mode On or Off.
IP Address
<192>168.254.254
Gateway Address
<000>000.000.000
Subnet Mask
<255>255.000.000
Rotate to select
octet field. Rotate
to change address.
Rotate to select
octet field. Rotate
to change address.
Rotate to select
octet field. Rotate
to change address.
Next
Next
Next
Next
Next
“Hidden” Menu *
Optional I/O
Board Menu **
* NOTE To activate the hidden menu “Edit Comms”,
press and hold Detail and Color/Tint buttons
simultaneously, then press Next.
** NOTE The Scan Coverter and Aux Scaler menus are
only available when the applicable optional I/O
board is installed.
H Size V
2048 2048
Scan
Converter
Rotate to adjust
H value. Rotate
to adjust V value.
Output Format
S-video/Comp
Output Standard
NTSC
Next
Next
Next
Next
Flicker Filter
3
Next
H Center V
2048 2048
Rotate to adjust
H value. Rotate
to adjust V value.
Rotate either to
select output format.
Rotate either to
select output standard.
H Filter
0
Next
Encoder Filter
0
Next
Rotate either to
adjust encoder filter.
Rotate either to
adjust flicker filter.
Rotate either to
adjust H filter.
Rotate either to adjust
RGB Delay value.
Switch Effect
Dissolve
MTP Pre-Peaking
Off
Test Pattern
Color Bars
Rotate either to
change Test Pattern.
Rotate either to turn
MTP Pre-Peaking
On or Off.
Rotate either to
change Switch Effect.
Internal temp
96 F 35 C
Reset to Factory
Press Detail
Calibrate Panels
Press size
Indicates Internal temperature
(not adjustable).
Press Size to callibrate
panel sizes.
Press Detail to reset unit
to factory settings.
Next
Next
Next
Next
Next
Next
RGB Delay
0.5 Seconds
Next
Input EDID
1024x768 60.0Hz
Next
Rotate to adjust
Resolution value
Rotate to adjust
Refresh rate.
Aspect Ratio
FILL
Rotate either to select
Aspect Ratio mode.
Next
Optional I/O
Board Menu **
Resol 1024x768
Refresh 60.00Hz
Aux
Scaler
Rotate to adjust
resolution. Rotate
to adjust refresh rate.
Aspect Ratio
Follow
Next
Next
Next
Detail
64
Next
Sync Polarity
H neg V neg
Rotate either to
select aspect
ratio mode.
Test Pattern
Crop
Next
Rotate either to
adjust detail level.
Rotate either to
select test pattern.
Output Type
RGBHV
Next
Rotate either to
select output type.
Rotate either to
adjust sync polarity
values.
Annotator • Operation 17