beautypg.com

Extron Electronics Annotator Setup Guide User Manual

Annotator • setup guide, Installation, Product category

background image

1

Product Category

IMPOR

TANT

:

Refer to www

.extron.com for

the complete user guide and

installation instructions.

Annotator • Setup Guide

The Extron Annotator (Annotation Graphics Processor) is a scaling product that allows a presenter to draw, point, or type on video
or computer source outputs using a touch panel, mouse, or keyboard.
This setup guide allows you to easily and quickly set up and configure your Annotator using step by step instructions. It covers
performing basic operations using the front panel controls and selected Simple Instruction Set (SIS

) commands.

NOTE:

For full installation, configuration, menus, and operation details, see the Annotator User Guide at

www.extron.com

Rack Mount
Bracket

Installation

Rear Panel Features

Power and video input connections

Output, user interface, and control connections

a

AC power connector

h

RGB/HD BNC connectors

o

RJ-45 Ethernet connector

b

RGB/HD VGA connectors (inputs 1 and 2)

i

RGB/HD VGA connectors

p

9-pin RS-232 connectors

c

Universal BNC connectors (input 3)

j

(Optional) output card*

q

Reset button and LED

d

Component/S-video/composite BNC connectors (input 4)

k

MTP twisted pair connector

e

S-video/composite video BNC connectors (input 5)

l

PS/2 mouse port

f

DVI connector (input 6)

m

PS/2 keyboard port

g

(Optional) HD/SD-SDI connector (input 7)

n

USB A ports

*scan converter shown

50/60 Hz

100-240V 2A

RGB/R-Y, Y, B-Y

LAN

USB

RS-232

2

1

R-Y

R/

B-Y

B/

4

3

R/

R-Y

R/

R-Y

B-Y

/C

G/Y

VID

G/

Y

B/

B-Y

B/C

B-Y

H/HV

VID

/Y

V

VID

LO-

RES

OUT

R-Y

Y/

G

C

C

HDSDI/SDI

H

V

S

I

N
P
U
T
S

O
U

T
P
U
T
S

RS-232

RESET

MOUSE

KEYBOARD

RGB/R-Y,Y,B-Y

VID

/Y

5

Y

MTP

DVI-D

7

6

7

1

2

5

3

4

6

15

16

10

9

13

11

14

8

RGB/R-Y,Y,B-Y

17

12

Mounting and Cabling

Step 1 — Mounting

Turn off or disconnect all equipment power sources and rack mount the Annotator
using the supplied brackets (see image at right).

Step 2 — Connect inputs

Connect inputs from video sources to the applicable connectors marked “Inputs”.
See

b

through

g

above for connector types and the image below for signal format.

RGBHV

H

/

HV

R

/R-Y

V

G

/Y

B

/B-Y

R

/R-Y

V

G

/Y

RGBS/ RGBcvS video

H/

HV

B

/B-Y

R-Y

VID

/Y

B-Y

/C

RGsB/

Component Video

(Y, R-Y, B-Y)

C

S-video

VID
/

Y

Composite

video

VID

/Y

C

Step 3 — Connect outputs

Connect video output devices to the applicable connectors marked “Outputs” (see

h

through

k

above).

CAUTION

Do not connect the MTP cable to the LAN port, or connect the LAN cable to the MTP port.

Step 4 — Connect user interface devices

PS/2 mouse and keyboard ports — Connect a mouse and/or a keyboard for annotation use.

Step 5 — Connect touch panel devices — USB or RS-232 connection

USB A ports — Connect a touch panel device to the Annotator via either of the USB A ports.
RS-232 — Using a NULL RS-232 cable only, connect a touch panel device to the Annotator via either of the RS-232 comm ports.

NOTE:

USB and RS-232 driver configuration is necessary and must be done using the Signal Processing Products Control
Program (SPPCP). Within the SPPCP program click Help > Contents for configuration instructions.
See the Annotator User Guide, for Simple Instruction Set (SIS

) command definitions, and SPPCP use.