Video output, Sync, Control/remote— signal processor – Extron Electronics Annotator User Guide User Manual
Page 100

Video output
Number/signal type ........................ 2 buffered scaled RGBHV, RGBS, RGsB, or HD component video (Y, R-Y, B-Y)
1 MTP
1 optional single link DVI-I (for unique scaled output); DVI-D; HD-SDI; or interlaced RGsB,
component video, S-video, composite video
Connectors .................................... 6 female BNC: RGB or component video
1 female 15-pin HD: RGB or component video
1 female RJ-45: output to an MTP device
1 slot for an optional output card with one of the following options:
· 1 female DVI-I (analog and digital, unique scaled output)
· 1 female DVI-I (digital output)
· 1 female BNC (HD-SDI output)
· 3 female BNC (interlaced RGsB, component, S-video, composite video output)
Nominal level ................................. 1 Vp-p for Y of component video and S-video, and for G of RGsB
0.8 Vp-p for SDI
0.7 Vp-p for RGB and for R-Y and B-Y of component video
0.3 Vp-p for C of S-video
Minimum/maximum levels .............. 0.0 V to 1.0 Vp-p
Impedance ..................................... 75 ohms
Scaled resolution ............................ 640x480
6,8,9
, 800x600
6,8,9
, 852x480
6,8,9
, 1024x768
6,8,9
, 1024x852
6,8,9
, 1024x1024
6,8,9
,
1280x768
6,8,9
, 1280x800
6,8,9
, 1280x1024
6,8,9
, 1360x765
6,8,9
, 1360x768
6,8,9
, 1365x768
6,8,9
,
1365x1024
6,8,9
, 1366x768
6,8,9
, 1400x1050
6,8
, 1440x900
6,8,9
, 1600x1200
6,8
, 1680x1050
6,8
,
1920x1200
6,8
HDTV: 480p
7,8
, 576p
6
, 720p
3,4,5,6,7,8
, 1080i
6,7,8
, 1080p
1,2,3,4,5,6,7,8
, 1080p CVT
8
,
2048x1080
1,2,3,4,5,6,7,8
SDTV: NTSC, PAL (with optional scan converter output card)
1
= 23.98 Hz,
2
= 24 Hz,
3
= 25 Hz,
4
= 29.97 Hz,
5
= 30 Hz,
6
= 50 Hz,
7
= 59.94 Hz,
8
=
60 Hz,
9
= 75 Hz
Formats .......................................... For DVI output: RGB and YCbCr digital video
Sync
Input type ...................................... RGBHV, RGBS, RGsB, RGBcvS, and component video (tri-level or bi-level)
Output type ................................... RGBHV, RGBS, RGsB, and component video (tri-level or bi-level)
Standards ....................................... NTSC 3.58, NTSC 4.43, PAL, SECAM
Optional SDI/HD-SDI input: SMPTE 259M-C, SMPTE 292M
Input level ...................................... 2.75 V to 5.0 Vp-p for RGBHV or RGBS
0.6 Vp-p for component video tri-level sync
0.3 Vp-p for component video bi-level sync or RGsB
Output level ................................... 5.0 Vp-p for RGBHV or RGBS
0.6 Vp-p for component video tri-level sync
0.3 Vp-p for component video bi-level sync or RGsB
Input impedance ............................ Horizontal: 75 ohms
Vertical: 510 ohms
Output impedance ......................... 75 ohms
Polarity ........................................... Positive or negative (selectable)
Control/remote— signal processor
Serial control port ........................... 2 RS-232/RS-422, female 9-pin D connectors (rear panel)
1 RS-232, 2.5 mm mini stereo jack (front panel)
Baud rate and protocol ................... 9600 (default), 19200, 38400, 115200 baud, adjustable; 8 data bits, 1 stop bit, no parity
Serial control pin configurations
9-pin D connector .................... RS-232: 2 = Tx, 3 = Rx, 5 = GND
RS-422: 2 = Tx-, 3 = Rx-, 5 = GND, 7 = Rx+, 8 = Tx+
2.5 mm mini stereo jack ........... Tip = Tx, ring = Rx, sleeve = GND
Ethernet control port ...................... 1 RJ-45 female connector
Ethernet data rate .......................... 10/100Base-T, half/full duplex with autodetect
Ethernet protocol ........................... ARP, ICMP (ping), IP, TCP, UDP, DHCP, HTTP, SMTP, Telnet
Ethernet default settings ................ Link speed and duplex level = autodetected
IP address = 192.168.254.254
Subnet mask = 255.255.0.0
Gateway = 0.0.0.0
DHCP = off
Annotator • Reference Material
94