GE Industrial Solutions AF-650 GP General Purpose Drive Programming Guide - Manual (Page 148)

Par. No.
# Parameter description Default value 4-set-up Change
during
operation
Conver-
sion
index
Type
H-48 Clockwise Direction [0] Normal All set-ups FALSE - Uint8
H-49 Motor Angle Offset Adjust [0] Manual All set-ups FALSE - Uint8
H-5#
H-50 Motor Magnetisation at Zero Speed 100 % All set-ups TRUE 0 Uint16
H-51 Min Speed Normal Magnetising [RPM] ExpressionLimit All set-ups TRUE 67 Uint16
H-52 Min Speed Normal Magnetising [Hz] ExpressionLimit All set-ups TRUE -1 Uint16
H-53 Model Shift Frequency ExpressionLimit All set-ups FALSE -1 Uint16
H-54 Voltage reduction in fieldweakening 0 V All set-ups FALSE 0 Uint8
H-55 U/f Characteristic - U ExpressionLimit All set-ups TRUE -1 Uint16
H-56 U/f Characteristic - F ExpressionLimit All set-ups TRUE -1 Uint16
H-58 Flystart Test Pulses Current ExpressionLimit All set-ups FALSE 0 Uint16
H-59 Flystart Test Pulses Frequency ExpressionLimit All set-ups FALSE 0 Uint16
H-6#
H-61 High Speed Load Compensation 100 % All set-ups TRUE 0 Int16
H-64 Resonance Dampening 100 % All set-ups TRUE 0 Uint16
H-65 Resonance Dampening Time Constant 5 ms All set-ups TRUE -3 Uint8
H-66 Min. Current at Low Speed ExpressionLimit All set-ups TRUE 0 Uint32
H-67 Torque Limit Factor Source [0] No function All set-ups TRUE - Uint8
H-68 Speed Limit Factor Source [0] No function All set-ups TRUE - Uint8
H-7#
H-70 Warning Current Low 0 A All set-ups TRUE -2 Uint32
H-71 Warning Current High ExpressionLimit All set-ups TRUE -2 Uint32
H-72 Warning Speed Low 0 RPM All set-ups TRUE 67 Uint16
H-73 Warning Speed High ExpressionLimit All set-ups TRUE 67 Uint16
H-74 Warning Reference Low -999999.999 N/A All set-ups TRUE -3 Int32
H-75 Warning Reference High 999999.999 N/A All set-ups TRUE -3 Int32
H-76 Warning Feedback Low
-999999.999 ReferenceFeed-
backUnit All set-ups TRUE -3 Int32
H-77 Warning Feedback High
999999.999 ReferenceFeed-
backUnit All set-ups TRUE -3 Int32
H-78 Missing Motor Phase Function ExpressionLimit All set-ups TRUE - Uint8
H-8#
H-80 Function at Stop [0] Coast All set-ups TRUE - Uint8
H-81 Min Speed for Function at Stop [RPM] ExpressionLimit All set-ups TRUE 67 Uint16
H-82 Min Speed for Function at Stop [Hz] ExpressionLimit All set-ups TRUE -1 Uint16
H-83 Precise Stop Function [0] Precise ramp stop All set-ups FALSE - Uint8
H-84 Precise Stop Counter Value 100000 N/A All set-ups TRUE 0 Uint32
H-85 Precise Stop Speed Compensation Delay 10 ms All set-ups TRUE -3 Uint8
H-87 Load Type [0] Passive load All set-ups TRUE - Uint8
H-88 Minimum Inertia ExpressionLimit All set-ups FALSE -4 Uint32
H-89 Maximum Inertia ExpressionLimit All set-ups FALSE -4 Uint32
H-9#
H-95 KTY Sensor Type [0] KTY Sensor 1 All set-ups TRUE - Uint8
H-96 KTY Thermistor Input [0] None All set-ups TRUE - Uint8
H-97 KTY Threshold level 80 °C 1 set-up TRUE 100 Int16
Parameter Lists AF-650 GP Programming Guide
DET-618C 147
4 4