Roland Fantom-Xa - Manual (Page 171)

171
Adding Effects
22: VK ROTARY
This type provides modified response for the rotary speaker, with
the low end boosted further.
This effect features the same specifications as the VK-7’s built-in
rotary speaker.
fig.MFX-22
23: CHORUS
This is a stereo chorus. A filter is provided so that you can adjust the
timbre of the chorus sound.
fig.MFX-23
24: FLANGER
This is a stereo flanger. (The LFO has the same phase for left and
right.) It produces a metallic resonance that rises and falls like a jet
airplane taking off or landing. A filter is provided so that you can
adjust the timbre of the flanged sound.
fig.MFX-24
Parameter Value Explanation
Speed # SLOW, FAST Rotational speed of the rotat-
ing speaker
Brake # OFF, ON Switches the rotation of the
rotary speaker.
When this is turned on, the
rotation will gradually
stop. When it is turned off,
the rotation will gradually
resume.
Woofer Slow
Speed 0.05–10.00 Hz Low-speed rotation speed of
the woofer
Woofer Fast
Speed 0.05–10.00 Hz High-speed rotation speed of
the woofer
Woofer Trans
Up 0–127 Adjusts the rate at which the
woofer rotation speeds up
when the rotation is switched
from Slow to Fast.
Woofer Trans
Down 0–127 Adjusts the rate at which the
woofer rotation speeds up
when the rotation is switched
from Fast to Slow.
Woofer Level 0–127 Volume of the woofer
Tweeter Slow
Speed 0.05–10.00 Hz Settings of the tweeter
The parameters are the
same as for the woofer.
Tweeter Fast
Speed 0.05–10.00 Hz
Tweeter Trans
Up 0–127
Tweeter Trans
Down 0–127
Tweeter Level 0–127
Spread 0–10 Sets the rotary speaker stereo
image. The higher the value
set, the wider the sound is
spread out.
Low Gain -15– +15 dB Gain of the low range
High Gain -15– +15 dB Gain of the high range
Level # 0–127 Output Level
Parameter Value Explanation
Filter Type OFF, LPF, HPF Type of filter
OFF: no filter is used
LPF: cuts the frequency range
above the Cutoff Freq
HPF: cuts the frequency range
below the Cutoff Freq
L out
R out
L in
R in
Rotary
2-Band EQ
2-Band EQ
L in
R in
Chorus
Chorus
L out
R out
2-Band
EQ
2-Band
EQ
Balance W
Balance W
Balance D
Balance D
Cutoff Freq 200–8000 Hz Basic frequency of the filter
Pre Delay 0.0–100.0 ms Adjusts the delay time from the
direct sound until the chorus
sound is heard.
Rate # 0.05–10.00 Hz, note Frequency of modulation
Depth 0–127 Depth of modulation
Phase 0–180 deg Spatial spread of the sound
Low Gain -15– +15 dB Gain of the low range
High Gain -15– +15 dB Gain of the high range
Balance # D100:0W–
D0:100W Volume balance between the di-
rect sound (D) and the chorus
sound (W)
Level 0–127 Output Level
Parameter Value Explanation
Filter Type OFF, LPF, HPF Type of filter
OFF: no filter is used
LPF: cuts the frequency range
above the Cutoff Freq
HPF: cuts the frequency range
below the Cutoff Freq
Cutoff Freq 200–8000 Hz Basic frequency of the filter
Pre Delay 0.0–100.0 ms Adjusts the delay time from
when the direct sound begins
until the flanger sound is heard.
Rate # 0.05–10.00 Hz, note Frequency of modulation
Depth 0–127 Depth of modulation
Phase 0–180 deg Spatial spread of the sound
Feedback # -98– +98 % Adjusts the proportion of the
flanger sound that is fed back
into the effect. Negative (-) set-
tings will invert the phase.
Low Gain -15– +15 dB Gain of the low range
High Gain -15– +15 dB Gain of the high range
Balance # D100:0W–
D0:100W Volume balance between the di-
rect sound (D) and the flanger
sound (W)
Level 0–127 Output Level
Parameter Value Explanation
R in R out
L in L out
Flanger
Feedback
Feedback
Flanger
Balance W
Balance D
Balance W
Balance D
2-Band
EQ
2-Band
EQ
Fantom-Xa_e.book 171 ページ ２００４年１０月２２日 金曜日 午後２時３分