Roland Fantom-Xa - Manual (Page 137)

137
Editing Songs
This function copies a specified area of sequencer data. It is
convenient for repeating the same phrase several times. You can
copy patterns to a phrase track, or copy data from a phrase track to a
pattern.
For details on the settings, refer to Basic Operation for Track
Editing (p. 133).
fig.Copy
Copying Phrases (Copy)
Parameter Value Explanation
Src Track/
Pattern TRK ALL,
TRK 1–16,
TEMPO,
PTN001–100 Copy-source track(s) or
pattern
TRK ALL: Phrase tracks 1–16, the beat track,
and the tempo track
TRK 1–16: Specified phrase track
TEMPO: Tempo track
PTN001–100: Specified pattern
Ch/Part ALL, Ch 1–16 MIDI channel of the data
to be copied
ALL: Copies all the sequencer data.
Ch 1–16: Copies only the sequencer data of a
specific MIDI channel.
* If you set “Src Track” to “TEMPO,” or if “Status”
is set to “System Exclusive,” “Tune Request” or
“Pattern Call,” this parameter will not be available.
Src Measure 0001– Range of copy-source
measures
If you set “For” to
“ALL,” all measures
will be specified.
For 1–ALL
Dst Track/
Pattern TRK ALL,
TRK 1–16,
TEMPO,
PTN001–100 Check/modify the copy-
destination track or pat-
tern.
TRK ALL: Phrase tracks 1–16, the beat track,
and the tempo track
TRK 1–16: Specified phrase track
TEMPO: Tempo track
PTN001–100: Specified pattern
* If you set “Src Track” to “ALL,” this parameter can
be set to either “ALL” or “PTN001–PTN100.” If
you select “PTN001–PTN100,” the data from the 16
phrase tracks will be merged as it is copied.
* If “TEMPO” is selected as “Src Track,” then only
“TEMPO” can be selected for this parameter.
Dst Mea-
sure 0001–END Copy-destination mea-
sure
* If you want the copy des-
tination to be right after
the last measure of a
song, set this parameter
to “END.”
Copy Mode MIX, REPLACE Specifies whether you
want to preserve the ex-
isting data in the copy
destination when copy-
ing.
MIX: Combines the data from the copy source
with the existing data in the copy destination.
REPLACE: Musical data in the copy destina-
tion will be erased (i.e., overwritten) when the
copy takes place. Only the sequencer data of the
MIDI channels specified by the Channel param-
eter will be overwritten, and data of other MIDI
channels will remain.
Copy Times 1–999 Number of times that the
data will be copied to the
copy destination
Status ALL, Note,
Poly Aftertouch,
Control Change,
Program Change,
Channel Aftertouch,
Pitch Bend,
System Exclusive,
Tune Request,
Pattern Call Type of data to be copied
* If “Src Track” is set to
“TEMPO,” this parame-
ter will not be available.
When “Status” is “Note” or “Poly Aftertouch”
Range Min 0 (C -)–127 (G9) Range of note numbers to
be copied
You can also specify
the key range by press-
ing keys on the key-
board.
Range Max
When “Status” is “Control Change”
Range Min 0–127 Range of controller num-
bers to be copied
Range Max
When “Status” is “Program Change”
Range Min 1–128 Range of program num-
bers to be copied
Range Max
Parameter Value Explanation
Fantom-Xa_e.book 137 ページ ２００４年１０月２２日 金曜日 午後２時３分