beautypg.com

FARGO electronic HDP600-LC CR100 User Manual

Page 7

background image

RESTRICTED USE ONLY

Fargo Electronics, Inc.

HDP600 High Definition Card Printer/Encoder User Guide (Rev. 2.5)

vii

Selecting the Card Hopper (HDP600 and HDP600-LC only) ______________________________ 7-19

Selecting the Card Hopper (HDP600 CR100 and HDP600-LC CR100 only) __________________ 7-20

Setting the Orientation ____________________________________________________________ 7-21

Specifying the number of Copies ____________________________________________________ 7-21

Selecting the Diagnostics button ____________________________________________________ 7-22

Selecting the Test Print button ______________________________________________________ 7-23

Selecting the About button _________________________________________________________ 7-24

Using the Device Options tab (HDP600/HDP600-LC)______________________________________ 7-26

Adjusting the Ribbon Type_________________________________________________________ 7-27

Selecting the Auto Ribbon Select option ______________________________________________ 7-28

Adjusting the Film Type___________________________________________________________ 7-29

Adjusting for the Color Matching____________________________________________________ 7-30

Adjusting for the Color Tone – Natural or Enhanced_____________________________________ 7-31

Adjusting for the Resin Dither ______________________________________________________ 7-32

Using the Print Both Sides option ___________________________________________________ 7-33

Using the Split 1 Set of Ribbon Panels option __________________________________________ 7-34

Using the Print Back Side First option ________________________________________________ 7-35

Using the Print Back Side Only option________________________________________________ 7-36

Using the Rotate Front 180 Degrees or Rotate Back 180 Degrees options ____________________ 7-37

Using the Print in Single Card Mode option____________________________________________ 7-38

Using the Disable Printing option____________________________________________________ 7-39

Using the Image Color tab (HDP600) ___________________________________________________ 7-40

Using the Image Transfer tab _________________________________________________________ 7-46

Adjusting the Image Position controls ________________________________________________ 7-47

Adjusting the Transfer Dwell Time and Temperature ____________________________________ 7-49

Using the K Panel Resin tab __________________________________________________________ 7-50

Selecting the Full Card with the K Panel Resin tab ______________________________________ 7-51

Selecting the Defined Area(s) with the K Panel Resin tab _________________________________ 7-52

Selecting the Undefined Area(s) with the K Panel Resin tab _______________________________ 7-53

Defining the Area to activate the Card Grid ____________________________________________ 7-54

Measuring the Total Card area ______________________________________________________ 7-55

Measuring the Area to be positioned on the Card________________________________________ 7-56

Selecting the Print YMC under the K and Print K Only options ____________________________ 7-57

Using the Magnetic Encoding tab ______________________________________________________ 7-59

Using the Encoding Mode option ____________________________________________________ 7-60

Encoding the Mode/Coercivity/Magnetic Track Selection_________________________________ 7-62

Reviewing the Magnetic Track Options _______________________________________________ 7-64

Reviewing the Enable MLE Support checkbox _________________________________________ 7-65

Reviewing the Verification options __________________________________________________ 7-66

Reviewing the Shift Data Left ______________________________________________________ 7-67

Reviewing the ISO Track Locations__________________________________________________ 7-68

Sending the Track Information ______________________________________________________ 7-69

Reviewing the Sample String _______________________________________________________ 7-70

Reviewing the ASCII Code and Character Table ________________________________________ 7-71

Using the Lamination tab (only with Card Lamination Module) ______________________________ 7-72

Selecting the Lamination Position ___________________________________________________ 7-73

Selecting the Lamination Side ______________________________________________________ 7-74

Selecting the Lamination Type ______________________________________________________ 7-75

Adjusting the Transfer Dwell Time and Transfer Temperature _____________________________ 7-76

Selecting the Sensors button and Defaults button________________________________________ 7-76

Selecting the Sensors button and Defaults button________________________________________ 7-77

Section 8: Cleaning ________________________________________________________ 8-1

Using the Required Supplies ________________________________________________________ 8-1

Safety Messages (review carefully)______________________________________________________ 8-2

Cleaning inside the Printer __________________________________________________________ 8-3