FARGO electronic HDP600-LC CR100 - Manual (Page 428)

RESTRICTED USE ONLY Fargo Electronics, Inc.
HDP600 High Definition Card Printer/Encoder User Guide (Rev. 2.5) 16-5
poor image quality problems, 4-91, 4-92
Port, 15-14
Portrait, 15-14
Portrait/Landscape, 7-21
Position magnetic data, 11-24, 11-25
positive/negative image placement values, 7-48
Potentiometer, 15-14
Power Port, 2-15
Power Switch, 2-15
power/data cables, 4-70
prevents magnetic encoding, 7-65
Print All Black With K Panel, 7-51
Print and Printers, 2-17
Print Area, 2-10
Print Back Side First option, 7-35
Print back side only, 7-36
print both sides, 7-33, 7-34
Print Both Sides option, 7-34, 7-36
Print Driver, 15-14
Print Head Lift Error, 4-9
Print Job, 15-14
Print K Only option, 7-57
Print Length, 2-6, 7-12, 7-14
Print Offset, 11-8, 11-9
Print Offset, Transfer TOF and Transfer EOF, 11-8, 11-9,
11-10, 11-18
Print Ribbon, 8-3
Print ribbon not installed., 4-10
Print Ribbon Options, 2-11
Print Ribbons, 2-21
Print Server, 15-14
Print Speed, 2-11
Print Speed-Batch Mode, 2-11
Print Station, 8-4
Print Status Screen, 2-18
Print Test Image, 4-18
Print Test Image, Setup Printer, Show Error Count, Show
Card Count and System Upgrade, 11-1
print the first page of a two-page document, 7-35
Print Timeout Error, 4-9
Print Width, 2-6, 7-12, 7-14
Print YMC Under K and Print K Only options, 7-57
Print YMC Under K/Print K Only options, 7-57
Print/Transfer Stations, 9-11
Printed cards
dark or light, 4-80
printed image, 7-48
printed text and barcodes, 7-57
Printer, 2-18
Printer, 11-6
Printer, 11-7
Printer Cleaning Kit, 8-4, 8-9, 8-10, 9-11
Printer Components, 2-14, 2-15
Printer Driver setup, 7-49
Printer's Firmware, 12-4
Printer's memory full, 7-38
Printhead, 2-14, 15-15
Printhead cleaning, 8-4
Printhead Cleaning Pen, 8-4
Printhead power cable, 4-70
Printhead Resistance, 11-21
Printhead Temp, 4-6
Printing Method, 2-10
Proper Settings, 7-5
Prox Card Encoder, 15-15
Prox card encoder not installed., 4-9
Proximity cards,
2-22
PVC, 15-15
PVC laminate,
2-22
Q
Queue, 15-15
R
RAM (Random Access Memory), 15-15
RAM Memory Error, 10-2
Rasterize, 15-15
Reboot, 15-15
recorded magnetic data, 7-67
Registration, 15-15
Regulatory Compliances, 2-5
Reject Hopper, 4-43
replace Sensor, 4-36
Replacing the Card Cleaning Tape, 8-5
Reset Printer, 4-70
Resin, 15-15
resin black (K) Panel, 7-52, 7-53, 7-54, 7-57
Resin Black Panel, 2-21
resin dither, 7-32
Resin Heat slide, 7-44
resin images, 7-44
Resin Thermal Transfer, 2-14
Resolution, 15-16
retries, 7-66
RFI (Radio Frequency Interference), 15-16
RFID (Radio Frequency Identification), 15-16
RGB, 4-19
RGB (Red/Green/Blue), 15-16
Ribbon, 15-16
Ribbon / Cards, 1-2
Ribbon cable, 15-16
Ribbon Drive adjustment, 11-20
Ribbon is out!, 4-10
ribbon Panels, 7-34
Ribbon Release Timeout Error, 4-10
Ribbon Sensor, 10-3
Ribbon Sensor Calibration, 4-95
Ribbon Tension adjustment, 11-19
ribbon type, 7-27, 7-29
Ribbon wrinkle problems, 4-83
Ribbon/Cards, 7-2, 8-2
RibbonTraq, 15-16
RibbonTraq marks, 10-3
Right Cards, 7-4
Right Cards/HDP Print Process, 7-4
RMA number, 15-16
Roller, 15-16
Roller Up/Down Error, 4-66
rotate front by 180 Degrees, 7-37
rotates image, 7-37
RS-232, 15-16