1 test commissioning with keypad control, Test commissioning with keypad control, Commissioning – Lenze 8400 BaseLine Manual User Manual
Page 88

Commissioning
Test commissioning
Test commissioning with keypad control
7
88
EDS84ABD302 EN 4.0
7.5.1
Test commissioning with keypad control
Step-by-step commissioning
1. Wiring of power terminals
Make use of the ”Electrical installation” chapter or the Mounting Instructions to wire the
power terminals according to the requirements of your device.
2. Wiring of control terminals.
Digital inputs at terminal X4
Assignment
Information
DI1
DI2
DI3
RFR
X4
24E
DO1
12I
AR A1U GND
DI4
RFR
z
Controller enable
RFR = High
z
Error reset
High → Low (edge-controlled)
3. If you can be sure that the frequency inverter is in the default state (Lenze setting),
you can skip this commissioning step. If not, establish the Lenze setting of the
frequency inverter as follows:
-0-
_
`
PASS
2 sec.
0000
_ `
....
`
....
....
`
_
_
_ `
....
C002
c001
01
-1-
8888
_ `
....
84BLMEN001
z
Select menu -1- (all parameters)
z
Press ”Enter” key
z
Set C002 code
z
Press ”Enter” key
z
Set c001 subcode
z
Press ”Enter” key
z
Set value ”01”
z
Press ”Enter” key
- p300 Mounting Instructions (12 pages)
- p300 Operating Instructions (37 pages)
- I/O system 1000 System Manual (744 pages)
- CS5800 Mounting Instructions (89 pages)
- CS5800 Operating Instructions (60 pages)
- Controller-based Automation (63 pages)
- Controller-based Automation (68 pages)
- 2121IB LECOM-Li (29 pages)
- HMI for visualisation / with control technology (96 pages)
- Controller 3200 C Operating Instructions (40 pages)
- c300 Operating Instructions (35 pages)
- EL 1800 Mounting Instructions (89 pages)
- EL 1800 Operating Instructions (57 pages)
- 3200 C (38 pages)
- 3200 C (195 pages)
- CPC 2800 Mounting Instructions (59 pages)
- CPC 2800 Operating Instructions (39 pages)
- CS 5000 DVI Mounting Instructions (86 pages)
- CS 5000 DVI Operating Instructions (53 pages)
- MP 800 DVI Mounting Instructions (88 pages)
- MP 800 Operating Instructions (43 pages)
- 8400 protec Manual (198 pages)
- 8400 motec Manual (121 pages)
- 8400 motec Mounting Instructions (164 pages)
- 9400 Manual (584 pages)
- 9400 Mounting Instructions (208 pages)
- 8400 (304 pages)
- 8400 (1494 pages)
- i700 Manual (159 pages)
- 8400 BaseLine Guide Quick Guide (10 pages)
- EZAEDE1000 (76 pages)
- EMF2180IB EthernetCAN (134 pages)
- EMF2181IB (154 pages)
- EMF2181IB (83 pages)
- EMF2177IB (18 pages)
- EMF2177IB (28 pages)
- E84AZESR RFI filter 3-29A (154 pages)
- E84AZESM Mains filter-RFI filter 42-96A (120 pages)
- ESVZAR0 RS-485 (33 pages)
- ESV SMV frequency inverter (66 pages)
- CANopen Controller-based Automation (110 pages)
- PROFIBUS Controller-based Automation (55 pages)
- EtherCAT Controller-based Automation (205 pages)
- PROFINET Controller-based Automation (44 pages)