INFICON Composer Gas Concentration Controller User Manual
Composer, Gas concentration controller
Table of contents
Document Outline
- Cover Page
- Title Page
- Trademarks
- Declaration Of Conformity
- Registration Card
- Warranty
- Table Of Contents
- Chapter 1 Getting Started
- 1.1 Introduction
- 1.2 Using this Manual
- 1.3 Performance Specifications
- 1.4 How To Contact Customer Support
- 1.5 Inventory of Supplied Items
- 1.6 Physical Requirements
- 1.7 Electrical Power Requirements
- 1.8 Environmental Requirements
- 1.9 Computer System Requirements
- 1.10 Installation
- Chapter 2 How the Instrument Works
- Chapter 3 Applications Guide
- 3.1 Advice and Tips
- 3.1.1 What is the Required Warm Up Time
- 3.1.2 When and How Often to Set the Reference Zero
- 3.1.3 How is Performance Affected if I Use the Factory Set Reference Zero Value?
- 3.1.4 What To Do when the Specific Heat Ratio for a Gas is Unknown?
- 3.1.5 What is the Ideal Operating Environment?
- 3.1.6 What is the Effect of Pressure Variation?
- 3.1.7 Should Sweep or Amplitude Track Mode Be Used?
- 3.1.8 What is the Effect of Flow Variation?
- 3.1.9 How Does This Instrumental Method Differ from Measuring the Speed Of Sound by Time Of Flight
- 3.1.10 What is the Long Term Stability of this Measurement System
- 3.1.11 Properties of Optional O-ring Materials
- 3.1.12 What Happens if the Reference Zero is Improperly Set
- 3.1.13 Composer Bulk Flow Control Configuration
- 3.1.14 Analog I/O Option — Concentration Control Configuration
- 3.1.15 How to Sample Flow with a Composer
- 3.2 Tutorials
- 3.1 Advice and Tips
- Chapter 4 Operation
- 4.1 Initialization and Setup
- 4.2 Calibration
- 4.3 How To Use The Instrument
- 4.3.1 How To Start The Instrument
- 4.3.2 How To Stop The Instrument
- 4.3.3 How To Shut Down The Instrument
- 4.3.4 Description and Purpose of Operating Modes
- 4.3.5 Description and Purpose of Displays
- 4.3.6 Description of Rear Panel
- 4.3.6.1 Description and Purpose of SYSTEM I/O Connector
- 4.3.6.2 SENSOR Connector
- 4.3.6.3 POWER Connector
- 4.3.6.4 Option Connector
- 4.3.6.5 CFGR1
- 4.3.6.6 CFGR2
- 4.3.6.7 RS-232C
- 4.3.6.8 CONCENTRATION OUT Connector
- 4.3.6.9 CONTROL OUT Connector
- 4.3.6.10 CONTROL IN Connector
- 4.3.6.11 Analog I/O Option
- 4.3.6.12 Safety Ground
- 4.3.7 Parameter Entry
- Chapter 5 Maintenance
- Chapter 6 Diagnosing Problems
- Chapter 7 External Communications
- Chapter 8 Software Guide
- 8.1 Introduction
- 8.2 Getting Started
- 8.3 Software Reference
- 8.3.1 Menu Bar
- 8.3.2 Toolbar
- 8.3.3 Ribbon Bar
- 8.3.4 Setup Communications Parameters
- 8.3.5 Setup Process Parameters
- 8.3.6 Sweep Mode
- 8.3.7 Amplitude Track Mode
- 8.3.8 Control State
- 8.3.9 Setup Data Log File
- 8.3.10 Setup Data Display
- 8.3.11 Gas Properties Database
- 8.3.12 Gas Concentration Calculator
- 8.3.13 I/O Status
- 8.3.14 About
- 8.4 Errors and Warnings Reporting
- 8.5 Multiple Composers
- Chapter 9 Bibliography
- Chapter 10 Glossary
- Chapter 11 Recommended Parts List
- Chapter 12 Quick Use Guide
- Index